2011 Lexus LS 460L RWDFACTORY OEM SERVICE PROCEDURE

Check For Intermittent Problems

  1. CHECK FOR INTERMITTENT PROBLEMS 

    HINT: 

    A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected in the ECU Data List function of the Techstream.

    1. Turn the engine switch off and connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG). Follow the directions on the Techstream to display the Data List and select areas where momentary interruptions are monitored.

      HINT: 

      A momentary interruption (open circuit) cannot be detected for 3 seconds after the engine switch is turned on (IG) (initial check).

      ABS / VSC / TR(A)C

      Item (Display) Measurement Item /
      Range (Display)
      Normal Condition Diagnostic Note
      FR Speed Open Front speed sensor RH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      FL Speed Open Front speed sensor LH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      RR Speed Open Rear speed sensor RH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      RL Speed Open Rear speed sensor LH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      EFI Communication Open SFI communication open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Yaw Rate Open Yaw rate sensor open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Deceleration Open Deceleration sensor open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Steering Open Steering angle sensor open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Master Cylinder Open Master cylinder pressure sensor open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Master Cylinder2 Open Master cylinder pressure sensor 2 open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Stroke Open Stroke sensor open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      FR Wheel Cylinder Open Front wheel cylinder pressure sensor RH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      FL Wheel Cylinder Open Front wheel cylinder pressure sensor LH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      RR Wheel Cylinder Open Rear wheel cylinder pressure sensor RH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      RL Wheel Cylinder open Rear wheel cylinder pressure sensor LH open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -
      Accumulator Open Accumulator pressure sensor open detection / Error or Normal Error: Momentary interruption
      Normal: Normal
      -

      HINT: 

      • If the ERROR display remains on, check the continuity between the ECU and the sensors, or between ECUs.
      • The ERROR display remains on for 1 second after the harness signal changes from momentary interruption (open circuit) to normal condition.

      While observing the screen, gently jiggle the connector or wire harness between the ECU and sensors, or between ECUs.

      Result

      ERROR display does not change.

      HINT: 

      The connector and/or wire harness will be in momentary interruption (open circuit) if the display changes. Repair or replace connector and/or wire harness as one of them is faulty.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.