2011 Lexus LS 460 AWDFACTORY OEM SERVICE PROCEDURE

Diagnostic Trouble Code Chart

HINT:Β 

  • If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the "See" in table below.
  • Inspect the fuses and relays related to this system before inspecting the trouble areas below.
ELECTRIC POWER CONTROL ECU DTC CHART

DTC Code Detection Item Trouble Area See
B22A0 IG2 Terminal Circuit Low - P IG2 fuse
- ECU-IG fuse
- Engine room No. 2 junction block, relay block
- Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22A0: IG2 Terminal Circuit Low
B22A1 Battery Current Sensor - Battery current sensor
- Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22A1: Battery Current Sensor
B22A6 THB Terminal Voltage Low - Battery current sensor
- Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22A6: THB Terminal Voltage Low
B22A8 VB Terminal Voltage - VSSR fuse
- Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22A8: VB Terminal Voltage
B22AB Open in Starter Switch Terminal - Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22AB: Open in Starter Switch Terminal
B22AC Alternater Stop Power Generation - Generator
- SFI system
Refer to DTC B22AC: Alternater Stop Power Generation; DTC B22AD: No Control for Power Generation of Alternator
B22AD No Control for Power Generation of Alternator - Generator
- SFI system
Refer to DTC B22AC: Alternater Stop Power Generation; DTC B22AD: No Control for Power Generation of Alternator
B22AE Open in Alternater Charge Line - Generator
- Wire harness
Refer to DTC B22AE: Open in Alternater Charge Line
B22B2 Power Cut Relay On Stuck - P-D/C CUT fuse
- Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22B2: Power Cut Relay On Stuck; DTC B22B3: Power Cut Relay Off Stuck
B22B3 Power Cut Relay Off Stuck - P-D/C CUT fuse
- Passenger side junction block (Electric power control ECU)
- Wire harness
Refer to DTC B22B2: Power Cut Relay On Stuck; DTC B22B3: Power Cut Relay Off Stuck
B22B6 Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator) - CAN communication system
- ECM
Refer to DTC B22B6: Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator); DTC B22B7: Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator); DTC B22B8: Communication Error with ECM / PCM "A" (Charge Mode Data); DTC B22BA: Communication Error with ECM / PCM "A" (Engine Speed Data); DTC B22BC: Communication Error with ECM / PCM "A" (Intake-Air Temperature Data); DTC B22BD: Communication Error with ECM / PCM "A" (Coolant Temperature Data)
B22B7 Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator) - CAN communication system
- ECM
Refer to DTC B22B6: Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator); DTC B22B7: Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator); DTC B22B8: Communication Error with ECM / PCM "A" (Charge Mode Data); DTC B22BA: Communication Error with ECM / PCM "A" (Engine Speed Data); DTC B22BC: Communication Error with ECM / PCM "A" (Intake-Air Temperature Data); DTC B22BD: Communication Error with ECM / PCM "A" (Coolant Temperature Data)
B22B8 Communication Error with ECM / PCM "A" (Charge Mode Data) - CAN communication system
- ECM
Refer to DTC B22B6: Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator); DTC B22B7: Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator); DTC B22B8: Communication Error with ECM / PCM "A" (Charge Mode Data); DTC B22BA: Communication Error with ECM / PCM "A" (Engine Speed Data); DTC B22BC: Communication Error with ECM / PCM "A" (Intake-Air Temperature Data); DTC B22BD: Communication Error with ECM / PCM "A" (Coolant Temperature Data)
B22BA Communication Error with ECM / PCM "A" (Engine Speed Data) - CAN communication system
- ECM
Refer to DTC B22B6: Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator); DTC B22B7: Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator); DTC B22B8: Communication Error with ECM / PCM "A" (Charge Mode Data); DTC B22BA: Communication Error with ECM / PCM "A" (Engine Speed Data); DTC B22BC: Communication Error with ECM / PCM "A" (Intake-Air Temperature Data); DTC B22BD: Communication Error with ECM / PCM "A" (Coolant Temperature Data)
B22BB Communication Error with Brake System Control Module (Vehicle Speed Data) - CAN communication system
- Skid control ECU
Refer to DTC B22BB: Communication Error with Brake System Control Module (Vehicle Speed Data)
B22BC Communication Error with ECM / PCM "A" (Intake-Air Temperature Data) - CAN communication system
- ECM
Refer to DTC B22B6: Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator); DTC B22B7: Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator); DTC B22B8: Communication Error with ECM / PCM "A" (Charge Mode Data); DTC B22BA: Communication Error with ECM / PCM "A" (Engine Speed Data); DTC B22BC: Communication Error with ECM / PCM "A" (Intake-Air Temperature Data); DTC B22BD: Communication Error with ECM / PCM "A" (Coolant Temperature Data)
B22BD Communication Error with ECM / PCM "A" (Coolant Temperature Data) - CAN communication system
- ECM
Refer to DTC B22B6: Communication Error with ECM / PCM "A" (Generate Voltage Data of Alternator); DTC B22B7: Communication Error with ECM / PCM "A" (Generate Rate Data of Alternator); DTC B22B8: Communication Error with ECM / PCM "A" (Charge Mode Data); DTC B22BA: Communication Error with ECM / PCM "A" (Engine Speed Data); DTC B22BC: Communication Error with ECM / PCM "A" (Intake-Air Temperature Data); DTC B22BD: Communication Error with ECM / PCM "A" (Coolant Temperature Data)
U0129 Lost Communication with Brake System Control Module - CAN communication system
- Passenger side junction block (Electric power control ECU)
Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
U0131 Lost Communication with Power Steering Control Module - CAN communication system
- Passenger side junction block (Electric power control ECU)
Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
U0142 Lost Communication with Gateway "A" - CAN communication system
- Passenger side junction block (Electric power control ECU)
Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
U0164 Lost Communication with HVAC Control Module - CAN communication system
- Passenger side junction block (Electric power control ECU)
Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
U1104 Lost Communication with Driving Support ECU - CAN communication system
- Passenger side junction block (Electric power control ECU)
Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
U1111 Lost Communication with Front Controller Module - CAN communication system
- Passenger side junction block (Electric power control ECU)
Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
U0100 Lost Communication with ECM / PCM "A" Β  Refer to DTC U0100: Lost Communication with ECM / PCM "A"; DTC U0129: Lost Communication with Brake System Control Module; DTC U0131: Lost Communication with Power Steering Control Module; DTC U0142: Lost Communication with Gateway "A"; DTC U0164: Lost Communication with HVAC Control Module; DTC U1104: Lost Communication with Driving Support ECU; DTC U1111: Lost Communication with Front Controller Module
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.