Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Power Steering System: Precaution: Precaution
- HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEMÂ
- The vehicle is equipped with an SRS (Supplemental Restraint System). Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing. This may cause a serious accident.
Before servicing (including inspection, replacement, removal and installation of parts), be sure to read the precautionary notices for the Supplemental Restraint System. Refer to PRECAUTION .
- The vehicle is equipped with an SRS (Supplemental Restraint System). Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing. This may cause a serious accident.
- PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF ELECTRONIC MOTOR POWER STEERING COMPONENTSÂ
- Be sure to align the front wheels straight ahead when removing and installing the power steering gear assembly.
- When disconnecting the steering sliding yoke sub-assembly and the pinion shaft of the power steering gear assembly, be sure to place matchmarks before servicing.
- After replacing the steering column assembly or power steering ECU assembly, calibrate the torque sensor zero point. Refer to CALIBRATIONÂ .
- HANDLING PRECAUTIONSÂ
- When handling the electronic parts:
- Avoid any impact to electronic parts such as ECUs and relays. Replace these parts with new ones if dropped or subjected to a severe blow.
- Do not expose any electronic parts to high temperature or humidity.
- Do not touch the connector terminals in order to prevent deformation or malfunctions due to static electricity.
- If the power steering ECU assembly has been replaced with a new one, initialize the rotation angle sensor value and calibrate the torque sensor zero point. Refer to CALIBRATIONÂ .
- When handling the power steering gear assembly:
- Avoid any impact to the power steering gear assembly, especially to the motor or torque sensor. Replace these parts with new ones if dropped or subjected to a severe blow.
- Do not pull on the wire harness when moving the power steering gear assembly.
- If the power steering gear assembly has been replaced with a new one, clear the rotation angle sensor calibration value, initialize the rotation angle sensor value, and calibrate the torque sensor zero point. Refer to CALIBRATIONÂ .
- When disconnecting and reconnecting the connectors:
- Turn the engine switch on (IG), center the steering wheel, and turn the engine switch off again before disconnecting the connectors related to the electronic power steering system.
- Ensure that the engine switch is off before reconnecting the connectors related to the power steering system. After reconnecting, center the steering wheel and turn the engine switch on (IG).NOTE:
Do not turn the engine switch on (IG) when the steering wheel is not centered.
- If the above operations are not carried out properly, the steering center point (zero point) will deviate, which may lead to a difference in steering effort between right and left. If there is a difference in steering effort between right and left, perform steering zero point calibration. Refer to CALIBRATIONÂ .
- When handling the electronic parts:
- PRECAUTIONS FOR CAN COMMUNICATIONÂ
- CAN communication is used to receive information from the skid control ECU, power steering ECU assembly, ECM, and steering angle sensor as well as to transmit warnings to the combination meter. It is also used for communication between terminals TC and TS of the DLC3. If there are any problems in the CAN communication lines, DTCs indicating communication line malfunctions are output.
- Perform troubleshooting for communication line problems if CAN communication DTCs are output. Be sure to start troubleshooting on the electric power steering system only when data communication is normal.
- Temporary fixing or repair with bypass wiring, etc. is impossible because the length and path of each CAN communication line is specified.
- BUS LINE REPAIRÂ
- After repairing the bus line with solder, wrap the repaired part with electrical tape.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
