2011 Lexus HS 250hFACTORY OEM SERVICE PROCEDURE

Data List / Active Test

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.

    1. Warm up the engine.
    2. Turn the power switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the power switch on (IG).
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Data List.
    7. According to the display on the Techstream, read the Data List.
    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Vehicle Speed Vehicle speed:
    Min.: 0 mph (0 km/h),
    Max.: 159 mph (255 km/h)    		 Actual vehicle speed Speed indicated on speedometer
    Engine Speed Engine speed:
    Min.: 0 rpm, Max.: 16383 rpm    		 850 to 950 rpm: Idling -
    Calculate Load Calculated load by hybrid vehicle control ECU:
    Min.: 0%, Max.: 100%
    • 11 to 30%: Idling
    • 12.1 to 30%: Running without load (2500 rpm)
    		 -
    Vehicle Load Vehicle load:
    Min.: 0%, Max.: 25700%    		 Actual vehicle load Load percentage in terms of maximum intake air flow amount
    MAF Air flow rate from mass air flow meter sub-assembly:
    Min.: 0 gm/sec, Max.: 655.35 gm/sec    		 2.0 to 4.3 gm/sec: Idling
    2.4 to 8.0 gm/sec: Running without load (2500 rpm)    		 If value approximately 0.0 gm/sec:
    • Mass air flow meter sub-assembly power source circuit open
    • VG circuit open or shorted

    If value 271.0 gm/sec or more:
    • E2G circuit open
    Atmosphere Pressure Atmospheric pressure:
    Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1913 mmHg)    		 Equivalent to atmospheric pressure -
    MAP Intake manifold pressure:
    Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1913 mmHg)
    • 80 to 110 kPa-a (600 to 826 mmHg-a): Power switch on (IG)
    • 20 to 40 kPa-a (150 to 300 mmHg-a): Idling
    		 -
    Coolant Temp Engine coolant temperature:
    Min.: -40°C (-40°F),
    Max.: 140°C (284°F)    		 80 to 100°C (176 to 212°F):
    After warming up
    • If value -40°C (-40°F): sensor circuit open
    • If value 140°C (284°F) or more: sensor circuit shorted
    Intake Air Intake air temperature:
    Min.: -40°C (-40°F),
    Max.: 140°C (284°F)    		 Equivalent to ambient air temperature
    • If value -40°C (-40°F): sensor circuit open
    • If value 140°C (284°F) or more: sensor circuit shorted
    Engine Run Time Engine run time:
    Min.: 0 s (second),
    Max.: 65535 s (seconds)    		 Time since engine started -
    Initial Engine Coolant Temp Initial engine coolant temperature:
    Min.: -40°C (-40°F),
    Max.: 120°C (248°F)    		 Coolant temperature when engine started Service data
    Initial Intake Air Temp Initial intake air temperature:
    Min.: -40°C (-40°F),
    Max.: 120°C (248°F)    		 Intake air temperature when engine started Service data
    Battery Voltage Battery voltage:
    Min.: 0 V, Max.: 65.5 V    		 11 to 16 V: Idling -
    Throttle Sensor Volt % Throttle valve opening percentage according to throttle position sensor:
    Min.: 0%, Max.: 100%    		 10 to 22%: Accelerator pedal released Value calculated based on the voltage at terminal VTA
    Throttl Sensor #2 Volt % Throttle valve opening percentage according to throttle position sensor No. 2:
    Min.: 0%, Max.: 100%    		 42 to 62%: Accelerator pedal released Value calculated based on the voltage at terminal VTA2
    System Guard System guard:
    ON or OFF    		 - Electronic throttle control system service data
    Throttle Idle Position Whether or not throttle position sensor detecting idling:
    ON or OFF
    • ON: Accelerator pedal released
    • OFF: Accelerator pedal fully depressed
    		 -
    Throttle Require Position Required throttle position:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 1.1 V: Idling -
    Throttle Sensor Position*1 Throttle position sensor:
    Min.: 0%, Max.: 100%    		 0%: Accelerator pedal released Recognition value for throttle opening angle on hybrid vehicle control ECU
    Throttle Position No. 1 Throttle position sensor No. 1 output voltage:
    Min.: 0 V, Max.: 4.98 V    		 - Electronic throttle control system service data
    Throttle Position No. 2 Throttle position sensor No. 2 output voltage:
    Min.: 0 V, Max.: 4.98 V    		 - Electronic throttle control system service data
    Throttle Position No. 1 Throttle position sensor No. 1:
    Min.: 0 V, Max.: 4.98 V
    • 0.5 to 1.1 V: Accelerator pedal released
    • 0.6 to 1.4 V: Fail-safe operating
    		 -
    Throttle Position No. 2 Throttle position sensor No. 2:
    Min.: 0 V, Max.: 4.98 V
    • 2.1 to 3.1 V: Accelerator pedal released
    • 2.1 to 3.1 V: Fail-safe operating
    		 -
    Throttle Position Command Throttle position command value:
    Min.: 0 V, Max.: 4.9 V    		 0.5 to 4.8 V -
    Throttle Sens Open Pos #1 Throttle sensor opener position No. 1:
    Min.: 0 V, Max.: 4.9 V    		 0.6 to 1.4 V Electronic throttle control system service data
    Throttle Sens Open Pos #2 Throttle sensor opener position No. 2:
    Min.: 0 V, Max.: 4.9 V    		 1.7 to 2.5 V Electronic throttle control system service data
    Throttle Sens Open #1 (AD) Throttle position sensor No. 1 output voltage (AD):
    Min.: 0 V, Max.: 4.9 V    		 0.5 to 4.8 V -
    Throttle Motor Whether throttle actuator control permitted:
    ON or OFF    		 ON: Power switch on (IG) and system normal
    OFF: Electronic throttle control system has failed    		 -
    Throttle Motor Current Throttle actuator current:
    Min.: 0 A, Max.: 19.9 A    		 0 to 3.0 A: Idling Electronic throttle control system service data
    Throttle Motor DUTY Throttle actuator duty ratio:
    Min.: 0%, Max.: 100%    		 10 to 22%: Idling after engine warmed up Electronic throttle control system service data
    Throttle Motor Current Throttle actuator current:
    Min.: 0 A, Max.: 19.92 A    		 0 to 3.0 A: Idling -
    Throttle Motor Open Duty Throttle actuator open duty ratio:
    Min.: 0%, Max.: 100%    		 0 to 40%: Idling When accelerator pedal depressed, duty ratio increased
    Throttle Motor Close Duty Throttle actuator close duty ratio:
    Min.: 0%, Max.: 100%    		 0 to 40%: Idling When accelerator pedal released quickly, duty ratio increased
    Throttle Motor Duty (Open) Throttle actuator duty ratio (open):
    Min.: 0%, Max.: 100%    		 0 to 40%: Idling Electronic throttle control system service data
    Throttle Motor Duty (Close) Throttle actuator duty ratio (close):
    Min.: 0%, Max.: 100%    		 0 to 40%: Idling Electronic throttle control system service data
    Throttle Fully Close Learn Throttle valve fully closed
    (learned value):
    Min.: 0 V, Max.: 4.98 V    		 0.4 to 1.0 V: Accelerator pedal released -
    ETCS Actuator Power ETCS power supply:
    ON or OFF    		 ON: Power switch on (IG) and system normal
    OFF: Electronic throttle control system has failed    		 -
    +BM Voltage +BM voltage:
    Min.: 0, Max.: 19.9 V    		 11 to 16 V: Power switch on (IG) and system normal Electronic throttle control system service data
    Actuator Power Supply Actuator power supply
    ON or OFF    		 ON: Idling -
    Clutch Current Clutch current:
    Min.: 0, Max.: 2.49 A    		 - -
    Fail Safe Drive Whether or not fail safe function is executed:
    ON or OFF    		 ON: Power switch on (IG) and system normal
    OFF: Electronic throttle control system has failed    		 -
    Fail Safe Drive (Main CPU) Whether or not fail safe function is executed:
    ON or OFF    		 ON: Power switch on (IG) and system normal
    OFF: Electronic throttle control system has failed    		 -
    Injector (Port) Injection duration for cylinder 1:
    Min.: 0 ms, Max.: 32.64 ms    		 1.5 to 2.7 ms: Idling -
    Injection Volum (Cylinder1) Injection volume (Cylinder 1):
    Min.: 0 ml, Max.: 2.047 ml    		 0 to 0.5 ml: Idling Quantity of fuel injection volume for 10 times
    Fuel Pump/Speed Status Fuel pump status:
    ON or OFF    		 - Active Test support data
    Vacuum Pump Key-off EVAP system leak detection pump status:
    ON or OFF    		 - Active Test support data
    EVAP (Purge) VSV EVAP (Purge) VSV control duty:
    Min.: 0%, Max.: 100%    		 0 to 50%: Idling, under purge control Order signal from hybrid vehicle control ECU
    EVAP Purge Flow Ratio of evaporative purge flow to intake air volume:
    Min.: 0%, Max.: 102.3%    		 0 to 100%: Idling Service data
    Purge Density Learn Value Learning value of purge density:
    Min.: -50, Max.: 349.99    		 -30 to 1: Idling Service data
    Vapor Pressure Pump Vapor pressure:
    Min.: 33.853 kPa (253.898 mmHg),
    Max.: 125.596 kPa (941.97 mmHg)    		 Approximately 100 kPa (750 mmHg) (absolute):
    Power switch on (IG)    		 EVAP system pressure monitored by canister pressure sensor
    Vapor Pressure (Calculated) Vapor pressure (calculated):
    Min.: -5.632 kPa (-42.24 mmHg),
    Max.: 715.264 kPa (5364.48 mmHg)    		 Approximately 100 kPa (750 mmHg) (absolute):
    Power switch on (IG)    		 EVAP system pressure monitored by canister pressure sensor
    EVAP System Vent Valve Key-off EVAP system vent valve status:
    ON or OFF    		 - Active Test support data
    EVAP Purge VSV Purge VSV status for EVAP control:
    ON or OFF    		 - Active Test support data
    Target Air-Fuel Ratio Ratio compared to stoichiometric level:
    Min.: 0, Max.: 1.998    		 0.8 to 1.2: Idling -
    AF Lambda B1 S1 Short-term fuel trim associated with bank 1 sensor 1:
    Min.: 0, Max.: 1.99
    • Value less than 1 (0.000 to 0.999) = Rich
    • Stoichiometric air fuel ratio = 1
    • Value greater than 1 (1.001 to 1.99) = Lean
    		 -
    AFS Voltage B1 S1 Air fuel ratio sensor output voltage for bank 1 sensor 1:
    Min.: 0 V, Max.: 7.99 V    		 2.6 to 3.8 V: Idling, engine warmed up Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors
    AFS Current B1 S1 Air fuel ratio sensor output current for bank 1 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA    		 -0.5 to 0.5 mA: Idling, engine warmed up Value becomes higher when fuel-cut executed under high engine speed
    O2S B1 S2 Heated oxygen sensor output voltage for bank 1 sensor 2:
    Min.: 0 V, Max.: 1.275 V    		 0.1 to 0.9 V:
    Driving at 47 mph (75 km/h)    		 Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors
    O2S Impedance B1S2 Heated oxygen sensor impedance (bank 1 sensor 2):
    Min.: 0 ohm, Max.: 21247.67 ohm    		 5 to 15000 ohm:
    After driving for 10 minutes or more in urban area    		 -
    Short FT #1 Short-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%    		 -20 to 20% Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
    Long FT #1 Long-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%    		 -20 to 20% Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value
    Total FT #1 Total fuel trim of bank 1
    Average value for fuel trim system of bank 1:
    Min.: -0.5, Max.: 0.496    		 -0.2 to 0.2: Idling -
    Fuel System Status #1 Fuel system status (bank 1):
    OL or CL or OLDrive or OLFault or CLFault    		 CL: Idling after warming up
    • OL (Open Loop): Has not yet satisfied conditions to go closed loop
    • CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
    • OLDrive: Open loop due to driving conditions (fuel enrichment)
    • OLFault: Open loop due to detected system fault
    • CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
    Fuel System Status #2 Fuel system status (bank 2):
    OL or CL or OLDrive or OLFault or CLFault    		 Unused -
    IGN Advance Ignition timing advance for No. 1 cylinder:
    Min.: -64 deg., Max.: 63.5 deg.    		 BTDC 5 to 25 deg.: Idling -
    Knock Feedback Value Feedback value of knocking:
    Min.: -64°CA, Max.: 1983.9°CA    		 -21 to 0°CA:
    Driving at 47 mph (75 km/h)    		 Service data
    Knock Correct Learn Value Correction learning value of knocking:
    Min.: -64°CA, Max.: 1983.9°CA    		 0 to 20°CA:
    Driving at 44 mph (70 km/h)    		 Service data
    VVT Control Status #1 VVT control status (bank 1):
    ON or OFF    		 - Active Test support data
    VVT Aim Angle #1*2 VVT aim angle (bank 1):
    Min.: 0%, Max.: 80%    		 0%: Idling VVT duty signal value during intrusive operation
    VVT Change Angle #1*2 VVT change angle (bank 1):
    Min.: 0 DegFR, Max.: 60 DegFR    		 0 to 5 DegFR: Idling Displacement angle during intrusive operation
    VVT OCV Duty #1*2 VVT camshaft timing oil control valve assembly operation duty:
    Min.: 0%, Max.: 100%    		 0 to 100% Requested duty value for intrusive operation
    Catalyst Temp B1 S1 Catalyst temperature (associated with sensor 1):
    Min.: -40°C (-40°F),
    Max.: 6513.5°C (11756.3°F)    		 Close to catalyst inlet temperature -
    Catalyst Temp B1 S2 Catalyst temperature (associated with sensor 2):
    Min.: -40°C (-40°F),
    Max.: 6513.5°C (11756.3°F)    		 Close to catalyst outlet temperature -
    Closed Throttle Position SW Closed throttle position switch:
    ON or OFF
    • ON: Throttle fully closed
    • OFF: Throttle open
    		 -
    Fuel Cut Condition Fuel cut determination flag:
    ON or OFF    		 - -
    Engine Oil Pressure SW Engine oil pressure switch:
    ON or OFF    		 - -
    Check Mode Check mode:
    ON or OFF    		 ON: Check mode ON Refer to CHECK MODE PROCEDURE 
    Misfire Test Result Check mode result for misfire monitor:
    Compl or Incmpl    		 - -
    OXS1 Test Result Check mode result for heated oxygen sensor (bank 1):
    Compl or Incmpl    		 - -
    A/F Test Results #1 Check mode result for air fuel ratio sensor (bank 1)
    Compl or Incmpl    		 - -
    Complete Parts Monitor Comprehensive component monitor:
    Not Avl or Avail    		 - -
    Fuel System Monitor Fuel system monitor:
    Not Avl or Avail    		 - -
    Misfire Monitor Misfire monitor:
    Not Avl or Avail    		 - -
    EGR/VVT Monitor EGR monitor:
    Not Avl or Avail    		 - -
    EGR/VVT Monitor EGR monitor:
    Compl or Incmpl    		 - -
    O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor:
    Not Avl or Avail    		 - -
    O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor:
    Compl or Incmpl    		 - -
    O2S(A/FS) Monitor O2S (A/FS) monitor:
    Not Avl or Avail    		 - -
    O2S(A/FS) Monitor O2S (A/FS) monitor:
    Compl or Incmpl    		 - -
    A/C Monitor A/C monitor:
    Not Avl or Avail    		 - -
    A/C Monitor A/C monitor:
    Compl or Incmpl    		 - -
    2nd Air Monitor 2nd air monitor:
    Not Avl or Avail    		 - -
    2nd Air Monitor 2nd air monitor:
    Compl or Incmpl    		 - -
    EVAP Monitor EVAP monitor:
    Not Avl or Avail    		 - -
    EVAP Monitor EVAP monitor:
    Compl or Incmpl    		 - -
    Heated Catalyst Monitor Heated catalyst monitor:
    Not Avl or Avail    		 - -
    Heated Catalyst Monitor Heated catalyst monitor:
    Compl or Incmpl    		 - -
    Catalyst Monitor Catalyst monitor:
    Not Avl or Avail    		 - -
    Catalyst Monitor Catalyst monitor:
    Compl or Incmpl    		 - -
    Component Monitor ENA Comprehensive component monitor:
    Unable or Enable    		 - -
    Component Monitor CMPL Comprehensive component monitor:
    Compl or Incmpl    		 - -
    Fuel System Monitor ENA Fuel system monitor:
    Unable or Enable    		 - -
    Fuel System Monitor CMPL Fuel system monitor:
    Compl or Incmpl    		 - -
    Misfire Monitor ENA Misfire monitor:
    Unable or Enable    		 - -
    Misfire Monitor CMPL Misfire monitor:
    Compl or Incmpl    		 - -
    EGR/VVT Monitor ENA EGR monitor:
    Unable or Enable    		 - -
    EGR/VVT Monitor CMPL EGR monitor:
    Compl or Incmpl    		 - -
    Heater Monitor ENA O2S (A/FS) heater monitor:
    Unable or Enable    		 - -
    Heater Monitor CMPL O2S (A/FS) heater monitor:
    Compl or Incmpl    		 - -
    O2S(A/FS) Monitor ENA O2S (A/FS) monitor:
    Unable or Enable    		 - -
    O2S(A/FS) Monitor CMPL O2S (A/FS) monitor:
    Compl or Incmpl    		 - -
    A/C Monitor ENA A/C monitor:
    Unable or Enable    		 - -
    A/C Monitor CMPL A/C monitor:
    Compl or Incmpl    		 - -
    2nd Air Monitor ENA 2nd air monitor:
    Unable or Enable    		 - -
    2nd Air Monitor CMPL 2nd air monitor:
    Compl or Incmpl    		 - -
    EVAP Monitor ENA EVAP monitor:
    Unable or Enable    		 - -
    EVAP Monitor CMPL EVAP monitor:
    Compl or Incmpl    		 - -
    Heated Cat Monitor ENA Heated catalyst monitor:
    Unable or Enable    		 - -
    Heated Cat Monitor CMPL Heated catalyst monitor:
    Compl or Incmpl    		 - -
    Catalyst Monitor ENA Catalyst monitor:
    Unable or Enable    		 - -
    Catalyst Monitor CMPL Catalyst monitor:
    Compl or Incmpl    		 - -
    # Codes (Include History) Number of emission related DTCs:
    Min.: 0
    Max.: 255    		 0: No emission related DTC detected -
    MIL MIL status:
    ON or OFF    		 ON: MIL ON -
    MIL ON Run Distance Distance traveled since MIL turned on:
    Min.: 0 Km (0 mile),
    Max.: 65535 Km (40724 mile)    		 Distance since DTC detected -
    Running Time from MIL ON Running time since MIL turned on:
    Min.: 0 min,
    Max.: 65535 min    		 Equivalent to running time since MIL turned on -
    Time after DTC Cleared Time since DTCs cleared:
    Min.: 0 min,
    Max.: 65535 min    		 Equivalent to time since DTCs cleared -
    Distance from DTC Cleared Distance traveled since DTCs cleared:
    Min.: 0 km (0 mile),
    Max.: 65535 km (40724 mile)    		 Equivalent to distance driven since DTCs cleared -
    Warm-up Cycle Cleared DTC Warm-up cycles since DTCs cleared:
    Min.: 0, Max.: 255    		 - Number of warm-up cycles since DTCs cleared
    OBD Requirements OBD requirement OBD2 -
    Number of Emission DTC Emission related DTCs
    Min.: 0
    Max.: 127    		 - Number of emission related DTCs
    TC and TE1 TC and CG (TE1) terminals of DLC3:
    ON or OFF    		 - Active Test support data
    Ignition Trig. Count Ignition counter for calculated misfire rate:
    Min.: 0, Max.: 800    		 0 to 800 -
    Cylinder #1 Misfire Count Misfire count of cylinder 1:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #2 Misfire Count Misfire count of cylinder 2:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #3 Misfire Count Misfire count of cylinder 3:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #4 Misfire Count Misfire count of cylinder 4:
    Min.: 0, Max.: 255    		 0 -
    All Cylinders Misfire Count All cylinders misfire count:
    Min.: 0, Max.: 255    		 0 -
    Misfire RPM Average engine speed when misfire occurred:
    Min.: 0 rpm, Max.: 6375 rpm    		 0 rpm: Misfire 0 -
    Misfire Load Average engine load when misfire occurred:
    Min.: 0 g/rev, Max.: 3.98 g/rev    		 0 g/rev: Misfire 0 -
    Electric Fan Motor Electric cooling fan motor:
    ON or OFF    		 ON: Electric cooling fan motor operating Active Test support data
    Idle Fuel Cut Fuel cut idle:
    ON or OFF    		 ON: Fuel cut operating -
    FC TAU Fuel cut TAU (Fuel cut with very light load):
    ON or OFF    		 ON: Fuel cut operating Fuel cut being performed during very light load to prevent incomplete engine combustion
    Model Code Model code - Identifies model code:
    ANF1##
    Engine Type Engine type - Identifies engine type:
    2AZFXE
    Cylinder Number Cylinder number:
    Min.: 0, Max.: 255    		 - Identifies number of cylinders:
    4
    Destination Destination - Identifies destination:
    A (America)
    Model Year Model year:
    Min.: 1900, Max.: 2155    		 - Identifies model year:
    2010
    System Identification System identification - Identifies engine system:
    HV (Hybrid)
    Requested Engine Torque Requested engine torque:
    Min.: 0 kW, Max.: 16383.75 kW    		 0 to 110 kW Flag information for hybrid vehicle
    HV Target Engine Speed Hybrid target engine speed:
    Min.: 0 rpm, Max.: 6375 rpm    		 0 to 6000 rpm Flag information for hybrid vehicle
    Actual Engine Torque Actual engine torque:
    Min.: -128 Nm, Max.: 127 Nm    		 Actual engine torque Flag information for hybrid vehicle
    Estimated Engine Torque Estimated engine torque:
    Min.: 0 Nm, Max.: 510 Nm    		 0 to 187 Nm Flag information for hybrid vehicle
    Engine Run Time Engine run time:
    Min.: 0 s (seconds), Max.: 255 s (seconds)    		 0 to 255 s Flag information for hybrid vehicle
    Request Engine Run Time Request engine run time:
    Min.: 0 s (seconds), Max.: 25.5 s (seconds)    		 0 to 25.5 s Flag information for hybrid vehicle
    Judge Time Engine Ignition Judgment time for completion of ignition:
    Min.: 0 s (seconds), Max.: 25.5 s (seconds)    		 0 to 25.5 s Flag information for hybrid vehicle
    Judge Time Engine Output Judgment time for time until engine output:
    Min.: 0 s (seconds), Max.: 25.5 s (seconds)    		 0 to 25.5 s Flag information for hybrid vehicle
    Fuel Level Fuel level:
    Empty or Not Emp    		 - -
    ISC Learning Idle speed control learning:
    Compl or Incmpl    		 - Flag information for hybrid vehicle
    F/C for Engine Stop Req Fuel cut for engine stop request:
    ON or OFF    		 - Flag information for hybrid vehicle
    Engine Independent Engine independent operation:
    Not Opr or Operate    		 - Flag information for hybrid vehicle
    Racing Operation Racing operation:
    Not Opr or Operate    		 - Flag information for hybrid vehicle
    Request Warm-up Request engine warm up:
    Not Req or Request    		 - Flag information for hybrid vehicle
    Engine Independent Control Engine independent control operation:
    Not Opr or Operate    		 - Flag information for hybrid vehicle
    ISC Learning Value Idle speed control learning value:
    Min.: 0 L/s, Max.: 19.92 L/s    		 - Flag information for hybrid vehicle

    HINT: 

    • Normal condition: If no idling conditions are specified, neutral (N) or park (P) should be selected, and the A/C switch and all accessory switches should be off.
    • *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
    • *2: Values are only displayed when performing the Active Tests: Control the VVT Linear (Bank1). For other Active Tests, the value will be 0.
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform the Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Warm up the engine.
    2. Turn the power switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the power switch on (IG).
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
    7. According to the display on the Techstream, perform the Active Test.
    Tester Display Test Part Control Range Diagnostic Note
    Control the Injection Volume Change injection volume -12.5 to 24.8%
    • All injectors tested at the same time
    • Perform test at less than 3000 rpm
    • Injection volume can be changed in 0.1 or 0.2% graduations within control range
    Control the Injection Volume for A/F Sensor Change injection volume Lower by 12.5% or increase by 25%
    • Perform test at less than 3000 rpm
    • Control the Injection Volume for A/F Sensor enables checking and graphing of air fuel ratio sensor and heated oxygen sensor voltage outputs
    • When conducting the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / AFS Voltage B1S1 and O2S B1S2
    Activate the VSV for EVAP Control Activate purge VSV control ON/OFF -
    Control the Fuel Pump / Speed Activate fuel pump (C/OPN Relay) ON/OFF Test possible when following conditions met:
    • Power switch on (IG)
    • Engine is stopped
    Connect the TC and TE1 Turn on and off TC and CG (TE1) connection ON/OFF
    • ON: TC and TE1 connected
    • OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
    Control the Electric Cooling Fan Control electric cooling fan motor ON/OFF -
    Control the ETCS Open/Close Slow Speed Throttle actuator Closed/Open Test possible when following conditions met:
    • Power switch on (IG)
    • Engine is stopped
    • Accelerator pedal fully depressed (Accelerator pedal position: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed Throttle actuator Closed/Open
    Control the VVT Linear (Bank1) Control VVT (bank 1) Between -128 and 127%
    This value added to present camshaft timing oil control valve control duty
    100%: Maximum advance
    -100%: Maximum retard
    • Engine stalls or idle roughly when VVT actuator operated at 100%
    • Test possible during idle
    Control the VVT System (Bank1) Turn on and off intake camshaft timing oil control valve assembly ON/OFF
    • Engine stalls or idles roughly when camshaft timing oil control valve assembly turned on
    • Normal engine running or idling when camshaft timing oil control valve assembly off
    • Test possible during idle
    Activate the Vacuum Pump Leak detection pump ON/OFF -
    Activate the VSV for Vent Valve Vent valve ON/OFF -
    Control the Select Cylinder Fuel Cut Selected Cylinder (cylinder #1 to #4) injector fuel cut ON/OFF Test is possible while the vehicle is stopped and the engine is idling.
    Control the All Cylinders Fuel Cut Fuel cut for all cylinders ON/OFF Test is possible while the vehicle is stopped and the engine is idling.
  3. SYSTEM CHECK 

    HINT: 

    Performing a System Check in the Utility menu enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Utility.
    5. Perform the System Check by referring to the table below.
    Tester Display Test Part Control Range Diagnostic Note
    Evaporative System Check
    (Automatic Mode)    		 Perform 5 steps in order to operate EVAP key-off monitor automatically 35°C (95°F) or less
    • If no DTCs in Pending after performing this test, system functioning normally
    Evaporative System Check
    (Manual Mode)    		 Perform 5 steps in order to operate EVAP key-off monitor manually 35°C (95°F) or less
    • Used to detect malfunctioning parts
Chapter Navigation
Return to Chapter: Data List / Active Test
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.