2011 Lexus CT 200hFACTORY OEM SERVICE PROCEDURE

Fuel Injector: Inspection: Inspection

  1. INSPECT FUEL INJECTOR ASSEMBLY 
    1. Check the resistance.
      1. Using an ohmmeter, measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 - 2 20°C (68°F) 11.6 to 12.4 Ω

        If the result is not as specified, replace the injector assembly.

    2. Check the operation.

      Inspect the injector injection volume.

      WARNING:

      Perform the inspection in a well-ventilated area.

      Do not perform the inspection near an open flame.

      1. Connect SST (fuel tube connector) to SST (hose), then connect them to the fuel pipe (vehicle side).
        Fig 1: Identifying Fuel Pipe Components
        GTY224524Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        TEXT IN ILLUSTRATION

        *1 SST
        (Hose)
        *2 Fuel Pipe (Vehicle Side)
        *3 SST
        (Clip)
        *4 SST
        (Fuel Tube Connector)
        • SST: 09268-31013 
          1. 09268-41500
          2. 90467-13001
          3. 95336-08070
        NOTE:

        Ensure that the SST connector O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and pipe.

      2. Install a new O-ring onto the fuel injector assembly.
        Fig 2: Identifying Fuel Injector Assembly Components
        GTY230618Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        TEXT IN ILLUSTRATION

        *1 SST
        (Hose)
        *2 SST
        (Clip)
        *3 SST
        (Adapter)
        *4 O-ring
        *5 SST
        (Clamp)
        *6 Vinyl Tube
      3. Connect SST (adapter and hose) to the injector assembly, and hold the injector assembly and union with SST (clamp).
        • SST: 09268-31013 
          1. 09268-41110
          2. 09268-41300
          3. 90467-13001
          4. 95336-08070
      4. Set the injector assembly in a graduated cylinder.
        WARNING:

        Install a suitable vinyl tube onto the injector assembly to prevent gasoline from spraying.

      5. Operate the fuel pump. Refer to ON-VEHICLE INSPECTION - Step 1 .
      6. Connect SST (wire) to the injector assembly and the auxiliary battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.
        • SST: 09842-30080 
        Fig 3: Connecting SST (Wire), Injector Assembly & Battery
        GTY261409Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        TEXT IN ILLUSTRATION

        *1 SST
        (Wire)
        *a Connect

        Standard Injection Volume

        Tester Connection Condition Specified Condition
        Positive terminal - Ground terminal Per 15 seconds 60 to 73 cc (3.7 to 4.5 cu.in.)

        Difference between each injector

        13 cc (0.8 cu.in.) or less

        NOTE:

        Always do the switching on the auxiliary battery side.

        If the injection volume is not as specified, replace the injector assembly.

    3. Inspect for leaks.
      1. In the condition above, disconnect the test probes of SST (wire) from the auxiliary battery and check for fuel leaks from the injector.

        Standard fuel drop

        1 drop or less every 25 minutes

        If there are excessive leaks, replace the injector assembly.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.