Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Initialization (To 08/2009): Initialization
- PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED
Necessary Procedures Procedure Details Effect / Inoperative Function When Necessary Procedures are not Performed Note Reset back door close position Fully close the back door to turn off the courtesy switch. - Power back door function
- Back door closer function
- If the back door is closed when disconnecting the cable from the battery terminal, it is not necessary to reset it.
- The power back door ECU controls the locked or unlocked state of the back door based on its memory. If the connector for the power back door ECU is disconnected and reconnected, the back door will need to be unlocked before it can be operated.
Correct the steering angle neutral point Fully turn the steering wheel to the right and left on the flat ground. - Parking assist monitor system
- Side monitor system (w/ Parking assist monitor system)
When "System initializing" is displayed on the multi-display, perform this procedure. NOTE:After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
- PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part Necessary Procedure Effect / Inoperative Function when Necessary Procedures are not Performed Note Power management control ECU Vehicle Identification Number (VIN) registration MIL comes on - Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system) - Dynamic radar cruise control system
- Pre-collision system
- Suspension control ECU - Registration of vehicle identification information
- Vehicle height offset calibration
- Vehicle specific control cannot be performed
- Vehicle height sensor data may be affected due to installation position, or vehicle height recognition may be erroneous
- Height control sensor Vehicle height offset calibration Vehicle height sensor data may be affected due to installation position, or vehicle height recognition may be erroneous - - Tire pressure warning ECU
- Tire pressure warning valve and transmitter
Code registration (Tire pressure warning system) - When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
- Tire pressure warning function
- Skid control ECU - Initialization and calibration of the linear solenoid valve
- Yaw rate and acceleration sensor zero point calibration
- ABS warning light illumination
- Slip indicator light illumination
- Brake warning light / yellow (minor malfunction) illumination
- VSC disabled or malfunctioning
- Brake actuator assembly - Bleed air
- Clearing stored linear solenoid valve calibration data
- Initialization and calibration of the linear solenoid valve
Brake does not operate properly - - Brake pedal stroke sensor
- Brake pedal
- Inspection and adjustment of brake pedal height
- Clearing stored linear solenoid valve calibration data
- Initialization and calibration of the linear solenoid valve
- ABS warning light illumination
- Slip indicator light illumination
- Brake warning light / yellow (minor malfunction) illumination
- VSC disabled or malfunctioning
- Yaw rate and acceleration sensor - Clearing zero point calibration data
- Yaw rate and acceleration sensor zero point calibration
- ABS warning light illumination
- Slip indicator light illumination
- Brake warning light / yellow (minor malfunction) illumination
- VSC disabled or malfunctioning
Necessary when wheel alignment adjustment. Power steering ECU Rotation angle sensor initialization and torque sensor zero point calibration - P/S warning light comes on
- EPS control
DTC (C1515/C1525) will be stored when the power steering ECU is replaced. Steering column Rotation angle sensor initialization and torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right - Spiral with sensor cable sub-assembly - Correct steering angle neutral point
- Steering angle setting
- Parking assist monitor system
- Side monitor system (w/ Parking assist monitor system)
- Parking assist ECU Parking assist ECU initialization - Parking assist monitor system
- Side monitor system
- Rear television camera Rear television camera optical axis (Camera position setting) Parking assist monitor system Necessary when vehicle height changes due to replacement of the suspension or tire, etc. - Side television camera
- Outer rear view mirror assembly (passenger side)
Side television camera optical axis (Camera position setting) Side monitor system (w/ Parking assist monitor system) Necessary when vehicle height changes due to replacement of the suspension or tire, etc. Roof console box assembly *1 Re-registration of codes in the garage door opener system - Register transmitter code
- Rolling code systems
Garage door opener system - - Certification ECU (smart key ECU assembly)
- ID code box (immobiliser code ECU)
- Steering lock ECU (steering lock actuator assembly)
- Key
Code registration (Engine immobiliser system) - Wireless door lock control system
- Smart access system with push-button start
- Engine start
- - Occupant classification ECU
- Front passenger seat
- Zero point calibration (Occupant classification system)
- Sensitivity check (Occupant classification system)
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger side)
- - Power window regulator motor
- Door window regulator
Initialize power window control system - Automatic door glass open/ close function
- Jam protection function
- Operation function after power switch is turned off
- Key-linked operation function
- Wireless transmitter-linked operation
Necessary when the regulator is removed and installed. - Sliding roof ECU (sliding roof drive gear sub-assembly)
- Sliding roof glass
- Sliding roof housing
Initializing sliding roof ECU (pulse sensor initial position setting) - Automatic slide open/close and tilt up/down function of sliding roof
- Jam protection function
- Operation function after power switch is turned off
Necessary when the sliding roof ECU is removed and installed (not necessary when the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and installed together with the sliding roof housing). AFS ECU (headlight swivel ECU assembly) Perform AFS ECU (headlight swivel ECU assembly) initialization - Headlight leveling function
- AFS
- Rear height control sensor sub-assembly RH *2 Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function - Necessary when the sensor is removed and installed
- Necessary when vehicle height changes due to replacement of the suspension
- Adjust the headlight aim after initializing the AFS ECU
- *1: w/ garage door opener system
- *2: w/o air suspension system
- VEHICLE IDENTIFICATION NUMBER (VIN) REGISTRATION (Hybrid Control System) NOTE:
The Vehicle Identification Number (VIN) must be input into the replacement power management control ECU.
HINT:
The VIN is in a 17-digit alphanumeric vehicle identification number. The Techstream is required to register the VIN.
- DESCRIPTION
- Read VIN: This process allows the VIN stored in the power management control ECU to be read, in order to confirm that the two VINs, provided with the vehicle and stored in the power management control ECU, are the same.
- Write VIN: This process allows the VIN to be input into the power management control ECU. If the power management control ECU is changed, or the power management control ECU VIN and the vehicle VIN do not match, the VIN can be registered, or overwritten in the power management control ECU by following this procedure.
- READ VIN
- Confirm the vehicle VIN.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Utility / VIN / VIN Read.
- WRITE VIN
- Confirm the vehicle VIN.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Utility / VIN / VIN Write.
- DESCRIPTION
- ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (Dynamic Radar Cruise Control System)
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
TEXT IN ILLUSTRATION*1 Approx. 10 m *2 Approx. 14 m WARNING:Exposure to radio frequency emissions is hazardous to your health. It is hazardous to your health to be within 20 cm (7.87 in.) of the device's radio frequency aperture.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
