Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 Lexus LS 460L RWDFACTORY OEM SERVICE PROCEDURE
Repair Instruction: Initialization: Initialization
PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED / RECONNECTED
| Necessary Procedures | Effects / Inoperative Functions When Necessary Procedures are not Performed | See |
|---|---|---|
| Correction of steering angle neutral point | Parking guidance function | Refer to INITIALIZATION |
| Rear door sunshade position reset operation | Rear door sunshade system function | Refer to INITIALIZATION |
| Reset power trunk lid system | Power trunk lid function | Refer to INITIALIZATION |
PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
| Replacement Part | Necessary Procedures | Effects / Inoperative Functions When Necessary Procedures are not Performed | See |
|---|---|---|---|
| ECM | Register VIN | DTC P0630 is output | Refer to REGISTRATION |
| Automatic transmission assembly (AA80F) |
|
|
Refer to INITIALIZATION |
| Automatic transmission assembly (AA80E) |
|
|
Refer to INITIALIZATION |
AA80F:
|
Learning by driving (Road test) |
|
Refer to INITIALIZATION |
AA80E:
|
Learning by driving (Road test) |
|
Refer to INITIALIZATION |
| TCM (AA80F) |
|
|
Refer to INITIALIZATION |
| TCM (AA80E) |
|
|
Refer to INITIALIZATION |
AA80F:
|
|
|
Refer to INITIALIZATION |
AA80E:
|
|
|
Refer to INITIALIZATION |
|
|
|
Refer to INITIALIZATION |
| Tire pressure warning ECU |
|
|
Refer to INITIALIZATION |
| Tire pressure warning valve and transmitter |
|
|
Refer to INITIALIZATION |
| Skid control ECU |
|
|
Refer to INITIALIZATION |
| Brake actuator |
|
Brake does not operate properly | Refer to INITIALIZATION |
|
|
|
Refer to INITIALIZATION |
| Yaw rate and acceleration sensor |
|
|
Refer to CALIBRATION |
| Electric parking brake ECU |
|
Electric parking brake does not operate normally | Refer to INITIALIZATION |
| Electric parking brake actuator |
|
|
Refer to INITIALIZATION |
|
Parking brake bedding | Parking brake performance may not be normal | Refer to INITIALIZATION |
|
Actuator angle neutral point calibration and initialization | Steering wheel off-center | Refer to CALIBRATION |
| Driving support ECU | Initialize driving support ECU | Systems controlled by driving support ECU do not operate | Refer to INITIALIZATION |
| Power steering gear assembly |
|
|
Refer to CALIBRATION |
| Power steering ECU |
|
|
Refer to CALIBRATION |
| Front seat set (Occupant classification ECU) |
|
|
Refer to INITIALIZATION |
|
Registration |
|
Refer to REGISTRATION |
| Millimeter wave radar sensor | Adjust front millimeter wave radar sensor | DTC C1A11 or C1A14 is output | Refer to ADJUSTMENT |
|
Adjust object recognition camera | DTC C1A22 or C1A23 is output | Refer to ADJUSTMENT |
| Steering angle sensor connector | Correction of steering angle neutral point | Parking guidance function | Refer to ADJUSTMENT |
| Television camera | Television camera optical axis (Camera position setting) |
Vehicle width extension lines and expected course are deviated | Refer to CALIBRATION |
| Parking assist ECU | Parking assist ECU initialization |
|
Refer to CALIBRATION |
| DCM (Telematics Transceiver) | DCM Activation | Safety connect system does not operative | Refer to DCM ACTIVATION |
| Power window regulator motor (All doors) |
Initialize power window control system |
|
Refer to INITIALIZATION |
| Inner rear view mirror |
|
Direction is not displayed correctly | Refer to CALIBRATION |
|
Position sensor initialization |
|
Refer to INITIALIZATION |
|
Position sensor initialization |
|
Refer to INITIALIZATION |
|
Reset power trunk lid system | Power trunk lid function | Refer to INITIALIZATION |
|
Rear curtain position reset operation | Rear curtain function | Refer to INITIALIZATION |
|
Initialize sliding roof drive gear sub-assembly |
|
Refer to INITIALIZATION |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
