2010 Lexus IS FFACTORY OEM SERVICE PROCEDURE

Steering Column Assembly: Installation: Installation

  1. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly.
      Fig 1: Identifying Matchmarks On Steering Intermediate Shaft Assembly And Steering Column Assembly
      GTY108825Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the bolt.

      Torque: 35 N*m (360 kgf*cm, 26 ft.*lbf) 

  2. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY 
    1. Align the matchmarks on the steering sliding yoke sub-assembly and the No. 2 steering intermediate shaft assembly.
      Fig 2: Identifying Matchmarks On Steering Sliding Yoke And Steering Intermediate Shaft Assembly
      GTY108824Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Temporarily install the bolt.

      HINT: 

      Torque the bolt after connecting the steering sliding yoke sub-assembly to the power steering link assembly.

  3. INSTALL STEERING COLUMN ASSEMBLY 
    1. Install the steering column assembly with the 4 nuts.
      Fig 3: Locating Steering Column Assembly Nuts
      GTY149220Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 26 N*m (260 kgf*cm, 19 ft.*lbf) 

    2. Connect the connectors and wire harness clamps to the steering column assembly.
    3. Install the clamp to the steering column hole shield.
      Fig 4: Identifying Steering Column Hole Shield Clamp
      GTY113406Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL BRAKE PEDAL RETURN SPRING  . Refer to INSTALLATION - Step 7
  5. INSTALL NO. 1 AIR DUCT 
    1. Engage the 2 claws to install the No. 1 air duct.
      Fig 5: Identifying No. 1 Air Duct
      GTY113400Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY  . Refer to INSTALLATION - Step 4
  7. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY 

    HINT: 

    Refer to the instructions for Installation of the driver side knee airbag assembly. Refer to INSTALLATION .

  8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 
  9. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
    1. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
      Fig 6: Identifying Turn Signal Switch Clip
      GTY149219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
  10. INSTALL TILT AND TELESCOPIC SWITCH  See step  1
  11. INSTALL STEERING COLUMN COVER 
    1. Engage the 4 clips and 2 guides to install the upper steering column cover onto the instrument panel cluster finish panel.
      Fig 7: Identifying Upper Steering Column Cover Clips And Guides
      GTY149218Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the claw to install the upper steering column cover.
      Fig 8: Identifying Upper Steering Column Cover Claw
      GTY136469Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Engage the 2 claws to install the lower steering column cover.
      Fig 9: Identifying Lower Steering Column Cover Claws
      GTY138703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.