2009 Lexus SC 430FACTORY OEM SERVICE PROCEDURE

Charging (Service Information): Generator: Reassembly: Reassembly

  1. INSTALL GENERATOR ROTOR ASSEMBLY 
      Fig 1: Installing Rotor To Drive End Frame
      GTY145108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place the drive end frame on the pulley.
    2. Install the rotor to the drive end frame.
  2. INSTALL GENERATOR COIL ASSEMBLY 
      Fig 2: Placing Generator Washer On Rotor
      GTY145109Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place the generator washer on the rotor.
    2. Fig 3: Pressing Coil
      GTY145161Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a 29 mm socket wrench and press, slowly press in the coil.
    4. Fig 4: Identifying Coil With Bolts
      GTY124131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Install the coil with the 4 bolts.

      Torque: 5.8 N*m ( 59 kgf*cm, 51 in.*lbf) 

  3. INSTALL GENERATOR PULLEY 
      Fig 5: Installing Generator Pulley
      GTY138679Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Install the pulley to the rotor shaft by tightening the pulley nut by hand.
    2. Hold SST (A) with a torque wrench, and tighten SST (B) clockwise to the specified torque.
      • SST: 09820-63011 

      Torque: 39 N*m ( 400 kgf*cm, 29 ft.*lbf) 

    3. Check that SST (A) is secured to the pulley shaft.
    4. Fig 6: Attaching Pulley Nut To SST
      GTY131388Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Mount SST (C) in a vise.
    6. Insert SST (B) into SST (C), and attach the pulley nut to SST (C).
    7. Fig 7: Removing Generator From SST
      GTY139733Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. To tighten the pulley nut, turn SST (A) in the direction shown in the illustration.

      Torque: 111 N*m ( 1,132 kgf*cm, 82 ft.*lbf) 

    9. Remove the generator from SST (C).
    10. Fig 8: Turning Generator From SST
      GTY126565Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    11. Turn SST (B) and remove SST (A and B).
  4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY 
      Fig 9: Placing Front Seal Plate Onto Coil
      GTY142080Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place the front seal plate onto the coil.
    2. Fig 10: Identifying Rear Seal Plate On Brush Holder
      GTY124583Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.