2009 Lexus LS 460L AWDFACTORY OEM SERVICE PROCEDURE

Diagnostic Trouble Code Chart

HINT:

  • If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the "DTC Code" below.
  • Inspect the fuses and relays related to this system before inspecting the trouble areas below.

    ELECTRIC POWER CONTROL ECU [Electric Power Control] 

    ELECTRIC POWER CONTROL ECU REFERENCE CHART

    DTC Code Detection Item Trouble Area
    B22A0  IG2 Terminal Circuit Low
    • P IG2 fuse
    • P-J/B fuse
    • Engine room No. 2 junction block, relay block
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22A1  Battery Current Sensor
    • Battery current sensor
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22A6  THB Terminal Voltage Low
    • Battery current sensor
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22A8  VB Terminal Voltage
    • VSSR fuse
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22AB  Open in Starter Switch Terminal
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22AC  Alternater Stop Power Generation
    • Generator
    • SFI system
    B22AD  No Control for Power Generation of Alternator
    • Generator
    • SFI system
    B22AE  Open in Alternater Charge Line
    • Generator
    • Wire harness
    B22B2  Power Cut Relay On Stuck
    • P-D/C CUT fuse
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22B3  Power Cut Relay Off Stuck
    • P-D/C CUT fuse
    • Passenger side junction block (Electric power control ECU)
    • Wire harness
    B22B6  Communication Error with ECM/PCM "A" (Generate Voltage Data of Alternator)
    • CAN communication system
    • ECM
    B22B7  Communication Error with ECM/PCM "A" (Generate Rate Data of Alternator)
    • CAN communication system
    • ECM
    B22B8  Communication Error with ECM/PCM "A" (Charge Mode Data)
    • CAN communication system
    • ECM
    B22BA  Communication Error with ECM/PCM "A" (Engine Speed Data)
    • CAN communication system
    • ECM
    B22BB  Communication Error with Brake System Control Module (Vehicle Speed Data)
    • CAN communication system
    • Skid control ECU
    B22BC  Communication Error with ECM/PCM "A" (Intake-Air Temperature Data)
    • CAN communication system
    • ECM
    B22BD  Communication Error with ECM/PCM "A" (Coolant Temperature Data)
    • CAN communication system
    • ECM
    U0100  Lost Communication with ECM/ PCM "A"
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
    U0129  Lost Communication with Brake System Control Module
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
    U0131  Lost Communication with Power Steering Control Module
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
    U0142  Lost Communication with Gateway "A"
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
    U0164  Lost Communication with HVAC Control Module
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
    U1104  Lost Communication with Driving Support ECU
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
    U1111  Lost Communication with Front Controller Module
    • CAN communication system
    • Passenger side junction block (Electric power control ECU)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.