2009 Lexus LS 460 AWDFACTORY OEM SERVICE PROCEDURE

Speed Sensor: Installation

  1. INSTALL SPEED SENSOR SP2 
    1. Install the speed sensor to the transmission case with the bolt.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

    2. Connect the sensor connector.
    Fig 1: Locating Speed Sensor SP2
    G04948416Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL SPEED SENSOR NC3 
    1. install the speed sensor to the transmission case with the bolt.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

    2. Connect the sensor connector.
    Fig 2: Locating Speed Sensor NC3
    G04948415Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL SPEED SENSOR NT 
    1. Coat a new O-ring with ATF and install it to the speed sensor.
    2. Using a T30 "TORX" wrench, install the speed sensor with the bolt.

      Torque: 6.8 N*m (69 kgf*cm, 60 in.*lbf) 

    3. Connect the sensor connector.
    Fig 3: Locating Speed Sensor NT
    G04948414Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL TRANSMISSION VALVE BODY ASSEMBLY 
    1. Install the spring and check ball body.
      Fig 4: Locating Spring And Check Ball Body
      G04948413Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Align the hole of the manual valve with the lever pin and connect the lever pin to the manual valve.
      Fig 5: Aligning Hole Of Manual Valve
      G04948421Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the valve body with the 17 bolts.

      Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf) 

      HINT:

      Each bolt length is indicated below.

      Bolt length: 

      21 mm (0.83 in.) for bolt A 

      31 mm (1.22 in.) for bolt B 

      64 mm (2.52 in.) for bolt C 

      Fig 6: Locating Valve Body And Bolts
      G04948422Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the detent spring and detent spring cover with the bolt.
      NOTE: Make sure to install the detent spring so that its roller is perpendicularly at the center of the manual valve lever.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      Fig 7: Locating Detent Spring And Detent Spring Cover
      G04948411Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Connect the 8 connectors to the solenoid valves.
    6. Connect the oil pressure switch connector.
    7. Coat a new O-ring with ATF and install it to the ATF temperature sensor.
    8. Install the ATF temperature sensor and lock plate with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    Fig 8: Locating ATF Temperature Sensor And Bolt
    G04948410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL VALVE BODY OIL STRAINER ASSEMBLY 
    1. Coat a new O-ring with ATF and install it to the oil strainer.
      NOTE: Ensure that the O-ring is not twisted or pinched.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.