Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK ECM (+B, +B1 VOLTAGE)Â
- Turn the ignition switch ON.
- Measure the voltage of the ECM connectors.
Standard voltageÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition E6-6 (+B) - E3-7 (E1) 9 to 14 V E6-5 (+B1) - E3-7 (E1) 9 to 14 V OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLEÂ
NG: Go to next stepÂ
- CHECK WIRE HARNESS (ECM - BODY GROUND)Â
- Disconnect the E3 ECM connector.
- Measure the resistance of the wire harness side connector.
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition E3-7 (E1) - Body ground Below 1 Ω NG: REPAIR OR REPLACE HARNESS AND CONNECTORÂ
OK: Go to next stepÂ
- CHECK ECM (IGSW VOLTAGE)Â
- Turn the ignition switch ON.
- Measure the voltage of the ECM connectors.
Standard voltageÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition E6-17 (IGSW) - E3-7 (E1) 9 to 14 V OK: Go to step  8
NG: Go to next stepÂ
- INSPECT FUSE (IGN)Â
- Remove the IGN fuse from the engine room No. 2 relay block.
- Measure the resistance of the IGN fuse.
Standard resistance:Â
Below 1 ΩÂ
NG: CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSEÂ
OK: Go to next stepÂ
- INSPECT RELAY (Marking: IG2)Â
- Remove the IG2 relay from the engine room No. 1 relay block.
- Measure the resistance of the IG2 relay.
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition 3-5 10 kΩ or higher 3-5 Below 1 Ω (when battery voltage is applied to terminals 1 and 2) NG: REPLACE IG2 RELAYÂ
OK: Go to next stepÂ
- INSPECT IGNITION SWITCHÂ
- Disconnect the I18 ignition switch connector.
- Measure the resistance of the ignition switch.
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Switch Condition Specified Condition 6 (IG2) - 7 (AM2) LOCK 10 kΩ or higher 6 (IG2) - 7 (AM2) ON Below 1 Ω NG: REPAIR OR REPLACE IGNITION SWITCHÂ
OK: Go to next stepÂ
- CHECK ECM (MREL VOLTAGE)Â
- Turn the ignition switch ON.
- Measure the voltage of the ECM connectors.
Standard voltageÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition E6-13 (MREL) - E3-7 (E1) 9 to 14 V NG: REPLACE ECMÂ
OK: Go to next stepÂ
- INSPECT FUSE (EFI)Â
- Remove the EFI fuse from the engine room No. 1 relay block and junction block.
- Measure the resistance of the EFI fuse.
Standard resistance:Â
Below 1 ΩÂ
NG: REPLACE EFI RELAYÂ
OK: Go to next stepÂ
- INSPECT EFI RELAY (Marking: EFI)Â
- Remove the EFI relay from the engine room No. 2 relay block.
- Measure the resistance of the EFI relay.
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition 3-5 10 kΩ or higher 3-5 Below 1 Ω (when battery voltage is applied to terminals 1 and 2) NG: REPAIR OR REPLACE HARNESS AND CONNECTORÂ
OK: Go to next stepÂ
- CHECK WIRE HARNESS (EFI RELAY (Marking: EFI) - ECM AND BODY GROUND)Â
- Check the wire harness between the EFI relay and ECM.
- Remove the EFI relay from the engine room No. 2 relay block.
- Disconnect the E6 ECM connector.
- Measure the resistance of the wire harness side connectors.
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition Relay block EFI relay terminal 2 - E6-13 (MREL) Below 1 Ω Relay block EFI relay terminal 2 or E6-13 (MREL) - Body ground 10 kΩ or higher - Check the wire harness between the EFI relay and body ground.
- Remove the EFI relay from the engine room No. 2 relay block.
- Measure the resistance of the wire harness side connectors.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Specified Condition Relay block EFI relay terminal 1 - Body ground Below 1 Ω
NG: REPAIR OR REPLACE HARNESS AND CONNECTORÂ
OK: REPAIR OR REPLACE HARNESS AND CONNECTOR (TERMINAL +B OF ECM - POSITIVE (+) BATTERY TERMINAL)Â
- Check the wire harness between the EFI relay and ECM.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
