2008 Lexus LX 570FACTORY OEM SERVICE PROCEDURE

Automatic Transmission Unit: Reassembly

  1. BEARING POSITION 
    Fig 1: Exploded View Of Bearing Components
    G05155183Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Bearing and Race Diameter 

    BEARING AND RACE DIAMETER

    Mark Front Race Diameter Inside / Outside Thrust Bearing Diameter Inside / Outside Rear Race Diameter Inside / Outside
    A 74.26 to 74.56 mm (2.92 to 2.94 in.) / 87.39 to 87.74 mm (3.44 to 3.45 in.) 71.96 to 72.26 mm (2.83 to 2.84 in.) / 85.25 to 85.6 mm (3.36 to 3.37 in.) -
    B 38.0 to 38.3 mm (1.50 to 1.51 in.)/53.9 to 54.1 mm (2.12 to 2.13 in.) 36.45 to 36.7 mm (1.44 to 1.45 in.) / 52.96 to 53.26 mm (2.09 to 2.10 in.) -
    C - 21.05 to 21.3 mm (0.829 to 0.839 in.) / 39.63 to 39.88 mm (1.56 to 1.57 in.) 22.8 to 23.1 mm (0.898 to 0.909 in.) / 44.5 to 44.75 mm (1.75 to 1.76 in.)
    D - 39.45 to 39.7 mm (1.55 to 1.56 in.) / 60.5 to 60.75 mm (2.38 to 2.39 in.) -
    E - 46.45 to 46.7 mm (1.83 to 1.84 in.) / 64.3 to 64.55 mm (2.53 to 2.54 in.) -
    F 55.0 to 55.2 mm (2.165 to 2.173 in.) / 68.8 to 69.3 mm (2.71 to 2.73 in.) 54.55 to 54.8 mm (2.15 to 2.16 in.) / 70.0 to 70.5 mm (2.76 to 2.78 in.) -
    G - 65.35 to 65.6 mm (2.57 to 2.58 in.) / 85.6 to 85.95 mm (3.37 to 3.38 in.) 62.85 to 63.1 mm (2.47 to 2.48 in.) / 82.3 to 82.6 mm (3.24 to 3.25 in.)
    H 39.67 to 39.87 mm (1.56 to 1.57 in.) / 56.5 to 57.0 mm (2.22 to 2.24 in.) 36.5 to 36.6 mm (1.437 to 1.441 in.) / 56.62 to 56.92 mm (2.23 to 2.24 in.) 36.45 to 36.7 mm (1.435 to 1.445 in.) / 56.5 to 57.0 mm (2.22 to 2.24 in.)
    I 21.05 to 21.3 mm (0.829 to 0.839 in.) / 39.5 to 39.8 mm (1.56 to 1.57 in.) 23.2 to 23.4 mm (0.913 to 0.921 in.) / 43.9 to 44.15 mm (1.73 to 1.74 in.) -
    J - 43.6 to 43.9 mm (1.72 to 1.73 in.) / 62.3 to 62.8 mm (2.45 to 2.47 in.) 47.15 to 47.4 mm (1.86 to 1.87 in.) / 66.9 to 67.1 mm (2.63 to 2.64 in.)
  2. INSTALL 1ST AND REVERSE BRAKE PISTON 
    1. Coat 3 new O-rings with ATF, and install them to the 1st and reverse brake piston.
      Fig 2: Identifying O-Rings
      G05155184Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 1st and reverse brake piston to the transmission case.
      NOTE:
      • Be careful not to damage the O-ring.
      • Make sure that the parking hole of the brake piston is on the bottom side by engaging the brake piston protrusion to the transmission case spline grooves.
    Fig 3: Installing 1st And Reverse Brake Piston To Transmission Case
    G05155185Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY 
    1. Place the brake return spring onto the 1st and reverse brake piston.

      SST 09380-60010 (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050) 

    2. Place SST on the spring retainer, and compress the return spring.
    3. Using SST, install the snap ring.

      SST 09350-30020 (09350-07070) 

      Fig 4: Placing Brake Return Spring Onto 1st And Reverse Brake Piston
      G05155150Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. SELECT NO. 4 BRAKE FLANGE 
    1. Measure distance A (from the tip of the 1st and reverse brake piston to the step in the transmission case) in the illustration.*1

      HINT:

      Standard distance A: 27.82 to 28.42 mm (1.09 to 1.12 in.)

      Fig 5: Measuring Distance From Tip Of 1st And Reverse Brake Piston To Step In Transmission Case
      G05155187Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Assemble the No. 4 brake flange, 7 No. 4 brake discs and 6 No. 4 brake plates, and measure distance B in the illustration.*2

      HINT:

      Standard distance B: 25.98 to 27.01 mm (1.02 to 1.06 in.)

      Fig 6: Measuring Distance B
      G05155188Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 4 brake selective flange indicated by the graph point.
      Fig 7: A And B Measurements Reference Graph
      G05155189Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Measure length H of the selected flange as shown in the illustration.

      HINT:

      Make sure that when the B measurement and H dimension of the selected flange are subtracted from the A measurement, the value is 0.961 to 1.261 mm (0.0378 to 0.0495 in.).

      No. 4 Brake Selected Flange Length H 

    BRAKE SELECTED FLANGE LENGTH

    Mark Length H
    0 0 mm (0 in.)
    2 0.15 to 0.25 mm (0.00590 to 0.00984 in.)
    4 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
    6 0.55 to 0.65 mm (0.0217 to 0.0256 in.)
    8 0.75 to 0.85 mm (0.0295 to 0.0335 in.)
    10 0.95 to 1.05 mm (0.0374 to 0.0413 in.)
  5. INSTALL REAR PLANETARY GEAR ASSEMBLY 
    1. Install the thrust bearing race.

      HINT:

      Use a small amount of MP grease to make the thrust bearing race stay securely in place.

      Bearing Race Diameter 

      BEARING RACE DIAMETER

      Item Inside Outside
      Race J 47.15 to 47.4 mm (1.86 to 1.87 in.) 66.9 to 67.1 mm (2.63 to 2.64 in.)
      Fig 8: Identifying Thrust Bearing Race
      G05155190Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 2 thrust needle roller bearings to the rear planetary gear.

      Bearing Diameter 

      BEARING DIAMETER

      Item Inside Outside
      Bearing 23.2 to 23.4 mm (0.913 to 0.921 in.) 43.9 to 44.15 mm (1.73 to 1.74 in.)
      Bearing J 43.6 to 43.9 mm (1.72 to 1.73 in.) 62.3 to 62.8 mm (2.45 to 2.47 in.)
      Fig 9: Installing Thrust Needle Roller Bearings To Rear Planetary Gear
      G05155191Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      Use a small amount of MP grease to make the thrust needle roller bearings stay securely in place.

    3. Install the rear planetary gear assembly.
    Fig 10: Installing Rear Planetary Gear Assembly
    G05155147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL BRAKE PLATE STOPPER SPRING 
    Fig 11: Installing Brake Plate Stopper Spring
    G05155193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSTALL REAR PLANETARY RING GEAR 
    1. Install the rear planetary ring gear flange to the rear planetary ring gear.
    2. Using a screwdriver, install the snap ring.
      Fig 12: Installing Snap Ring
      G05155144Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the 3 thrust bearing races, thrust needle roller bearing and planetary ring gear with the rear planetary ring gear flange to the intermediate shaft.

      HINT:

      Use a small amount of MP grease to make the thrust needle roller bearing and races stay securely in place.

    Fig 13: Installing Thrust Bearing Races, Thrust Needle Roller Bearing And Planetary Ring Gear
    G05155195Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Bearing and Race Diameter 

    BEARING AND RACE DIAMETER

    Item Inside Outside
    Front race H 39.67 to 39.87 mm (1.56 to 1.57 in.) 56.5 to 57.0 mm (2.22 to 2.24 in.)
    Bearing H 36.5 to 36.6 mm (1.437 to 1.441 in.) 56.62 to 56.92 mm (2.23 to 2.24 in.)
    Rear race H 36.45 to 36.7 mm (1.435 to 1.445 in.) 56.5 to 57.0 mm (2.22 to 2.24 in.)
    Race I 21.05 to 21.3 mm (0.829 to 0.839 in.) 39.5 to 39.8 mm (1.56 to 1.57 in.)
  8. INSTALL INTERMEDIATE SHAFT WITH REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR 
    1. Install the intermediate shaft with the rear planetary ring gear flange and rear planetary ring gear to the transmission case.
    Fig 14: Installing Intermediate Shaft With Rear Planetary Ring Gear Flange And Rear Planetary Ring Gear
    G05155196Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSTALL NO. 4 BRAKE DISC SET 
    1. Install the flange, 7 discs, 6 plates and selected flange.

      Install in order: 

      F - D - P - D - P - D - P - D - P - D - P - D - P - D - S/F 

      HINT:

      F = Flange

      D = Disc

      P = Plate

      S/F = Selected flange

      NOTE: Before assembling new discs, soak them in ATF for at least 2 hours.
    Fig 15: Installing No. 4 Brake Disc Set
    G05155197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSTALL NO. 3 1-WAY CLUTCH INNER RACE 
    1. Install the 1 -way clutch inner race to the No. 3 1-way clutch assembly.
      NOTE: Do not mistake the direction of the 1-way clutch inner race.
  11. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY  (See INSPECTION )
    Fig 16: Installing No. 3 1-Way Clutch Inner Race
    G05155198Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY 
    1. Install the 1-way clutch assembly to the transmission case.
      Fig 17: Installing No. 3 1-Way Clutch Assembly
      G05155199Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, install the snap ring.

      SST 09350-30020 (09350-07060) 

      Fig 18: Installing Snap Ring
      G05155140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL NO. 2 BRAKE PISTON 
    1. Coat 2 new O-rings with ATF, and install them to the brake piston.
    2. Press the brake piston into the brake cylinder with both hands.
      NOTE: Be careful not to damage the O-rings.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.