2008 Lexus LX 570FACTORY OEM SERVICE PROCEDURE

Automatic Transmission Unit: Disassembly

  1. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH 
    1. Remove the nut, spring washer and control shaft lever.
    Fig 1: Removing Transmission Control Shaft Lever RH
    G05760783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Using a screwdriver, bend the tabs of the lock washer.
    2. Remove the nut, lock washer and bolt.
    3. Remove the park/neutral position switch.
    Fig 2: Removing Park/Neutral Position Switch Assembly
    G05155047Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE SPEED SENSOR 
    1. Remove the 2 bolts and 2 speed sensors.
    2. Remove the 2 O-rings from the sensors.
    Fig 3: Removing Speed Sensor
    G05155048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE TRANSMISSION OIL COOLER ASSEMBLY 
    1. Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.
    2. Separate the transmission oil cooler from the transmission oil thermostat.
    3. Remove the 4 O-rings.
    Fig 4: Removing Transmission Oil Cooler Assembly
    G05760745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE 
    1. Remove the 2 bolts.
    2. Remove the breather tube.
    3. Remove the O-ring from the tube.
    Fig 5: Removing Automatic Transmission Breather Tube
    G05647639Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE AUTOMATIC TRANSMISSION HOUSING 
    1. Remove the 14 bolts.
    2. Remove the transmission housing.
    Fig 6: Removing Automatic Transmission Housing
    G05155052Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE REAR ADAPTOR TRANSFER 
    1. Remove the 10 bolts.
    2. Remove the rear adaptor transfer.

      HINT:

      Tap on the circumference of the extension housing with a plastic-faced hammer to remove the rear adaptor transfer.

      Fig 7: Removing Rear Adaptor Transfer
      G05155304Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE TRANSMISSION CASE ADAPTOR OIL SEAL 
    1. Using a screwdriver, pry out the oil seal.
      NOTE: Be careful not to damage the rear adaptor transfer.

      HINT:

      Wrap the tip of the screwdriver with tape.

      Fig 8: Removing Transmission Case Adaptor Oil Seal
      G05155054Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE TRANSFER CASE ADAPTER RADIAL BALL BEARING 
    1. Using a screwdriver, remove the snap ring.
    2. Using SST and a press, press out the bearing.

      SST 09950-60010 (09951-00650), 09950-70010 (09951-07150) 

      Fig 9: Removing Transfer Case Adapter Radial Ball Bearing
      G05155055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY 
    1. Install the transmission case to an overhaul attachment.
    Fig 10: Installing Transmission Case To Overhaul Attachment
    G05155056Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY 
    NOTE: Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.
    1. Remove the drain plug, 12 bolts, oil pan and gasket.
  12. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY  (See INSPECTION )
    Fig 11: Removing Automatic Transmission Oil Pan Sub-Assembly
    G05760793Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE VALVE BODY OIL STRAINER ASSEMBLY 
    1. Turn over the transmission.
    2. Remove the 4 bolts and oil strainer from the valve body.
    3. Remove the O-ring from the oil strainer.
    Fig 12: Removing Valve Body Oil Strainer Assembly
    G05647461Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE TRANSMISSION WIRE 
    1. Remove the 2 bolts and 2 temperature sensor clamps.
    2. Disconnect the 2 ATF temperature sensors.
    3. Disconnect the 9 connectors from the solenoid valves.
      Fig 13: Locating Bolts And Temperature Sensor Clamps
      G05155059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 2 bolts and pull out the No. 1 and No. 2 transmission wires.
      Fig 14: Locating Bolts For No. 1 And No. 2 Transmission Wires
      G05155060Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 2 O-rings from the transmission wire connectors.
  15. REMOVE TRANSMISSION VALVE BODY ASSEMBLY 
    1. Remove the bolt, detent spring cover and detent spring.
      Fig 15: Removing O-Rings From Transmission Wire Connectors
      G05155061Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 19 bolts.
    3. Remove the valve body assembly.
    Fig 16: Locating Bolts For Valve Body Assembly
    G05154849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE TRANSMISSION CASE GASKET 
    1. Remove the 3 gaskets.
    Fig 17: Removing Transmission Case Gasket
    G05155063Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE BRAKE DRUM GASKET 
    1. Remove the 3 gaskets.
    Fig 18: Removing Brake Drum Gasket
    G05155064Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE CHECK BALL BODY 
    1. Remove the check ball body and spring.
    Fig 19: Removing Check Ball Body
    G05155290Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE C-2 ACCUMULATOR PISTON 
    1. While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.
    2. Remove the 2 O-rings from the piston.
      NOTE: Be careful as the C-3 and B-3 accumulator pistons may jump out.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.