Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
How To Proceed With Troubleshooting
HINT:
- The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.
- *: Use the Techstream.
- VEHICLE BROUGHT TO WORKSHOPÂ
- CUSTOMER PROBLEM ANALYSISÂ
- INSPECT BATTERY VOLTAGEÂ
Standard Voltage:Â
11 to 14 VÂ
If the voltage is below 11V, recharge or replace the battery before proceeding.
- CONNECT TECHSTREAM TO DLC3* NEXTÂ
- CHECK AND CLEAR DTCS AND FREEZE FRAME DATA*Â
- Refer to the DTC Check / Clear (See DTC CHECK/CLEARÂ ).
- VISUAL INSPECTIONÂ
- SETTING CHECK MODE DIAGNOSIS*Â
- Refer to the Check Mode Procedure (See DTC CHECK/CLEARÂ ).
- PROBLEM SYMPTOM CONFIRMATIONÂ
- Refer to the Road Test (See ROAD TESTÂ ).
ResultÂ
RESULT DESCRIPTIONResult Proceed to Symptom does not occur A Symptom occurs B B:Â GO TO STEP Â 10
A: Go to next stepÂ
- SYMPTOM SIMULATIONÂ
- Refer to the Electronic Circuit Inspection Procedure (See ELECTRONIC CIRCUIT INSPECTION PROCEDURE ).
- DTC CHECK*Â
- Refer to the DTC Check / Clear (See DTC CHECK/CLEARÂ ).
ResultÂ
RESULT DESCRIPTIONResult Proceed to DTC is not output A DTC is output B B:Â GO TO STEP Â 18
A: Go to next stepÂ
- BASIC INSPECTIONÂ
- Refer to the Automatic Transmission Fluid (See AUTOMATIC TRANSMISSION FLUIDÂ ).
- Refer to the Park/Neutral Position Switch (See ON-VEHICLE INSPECTIONÂ ).
- Refer to the Shift Lever Assembly (See ON-VEHICLE INSPECTIONÂ ).
NG:Â GO TO STEP Â 21
OK: Go to next stepÂ
- MECHANICAL SYSTEM TESTSÂ
- Refer to the Mechanical System Tests (See MECHANICAL SYSTEM TESTSÂ ).
NG:Â GO TO STEP Â 17
OK: Go to next stepÂ
- HYDRAULIC TESTÂ
- Refer to the Hydraulic Test (See HYDRAULIC TESTÂ ).
NG:Â GO TO STEP Â 17
OK: Go to next stepÂ
- MANUAL SHIFTING TESTÂ
- Refer to the Manual Shifting Test (See MANUAL SHIFTING TESTÂ ).
NG:Â GO TO STEP Â 16
OK: Go to next stepÂ
- PROBLEM SYMPTOMS TABLE CHAPTER 1Â
- Refer to the Problem Symptoms Table (See PROBLEM SYMPTOMS TABLEÂ ).
NG:Â GO TO STEP Â 19
OK: Go to next stepÂ
- PROBLEM SYMPTOMS TABLE CHAPTER 2Â
- Refer to the Problem Symptoms Table (See PROBLEM SYMPTOMS TABLEÂ ).
- PART INSPECTIONÂ
NG:Â GO TO STEP Â 21
OK: Go to next stepÂ
- DTC CHARTÂ
- Refer to the Diagnostic Trouble Code Chart (See DIAGNOSTIC TROUBLE CODE CHARTÂ ).
- CIRCUIT INSPECTIONÂ
- IDENTIFICATION OF PROBLEMÂ
- REPAIR OR REPLACEÂ
- CONFIRMATION TESTÂ
NEXT: ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
