Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK THAT MIL IS ILLUMINATEDÂ
- Perform troubleshooting in accordance with the table below.
ResultÂ
RESULT REFERENCEResult Proceed to MIL remains ON A MIL does not illuminate B B: Go to step  5
A: Go to Next StepÂ
- Perform troubleshooting in accordance with the table below.
- CHECK WHETHER MIL TURNS OFFÂ
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
- Check if any DTCs are output. Note down any DTCs.
- Clear DTCs (See DTC CHECK/CLEAR ).
- Check if the MIL goes off.
Standard:Â
MIL goes offÂ
NG: Go to step  3
OK: REPAIR CIRCUITS INDICATED BY OUTPUT DTCSÂ (See DIAGNOSTIC TROUBLE CODE CHART )
- CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)Â
- Disconnect the A38 ECM connector.
- Turn the engine switch on (IG).
- Check that the MIL is not illuminated.
OK: MIL is not illuminated.Â
NG: Go to step  4
OK: REPLACE ECMÂ (See ECMÂ )
- CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)Â
- Disconnect the A38 ECM connector.
- Disconnect the E77 combination meter connector.
- Measure the resistance according to the value(s) in the table below.
Standard ResistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Condition Specified Condition A38-24 (W) or E77-18 (CHK) - Body ground Always 10 kΩ or higher NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK: REPLACE COMBINATION METER ASSEMBLYÂ (See REMOVAL )
- CHECK THAT MIL IS ILLUMINATEDÂ
- Check if the MIL is illuminated when the engine switch is turned on (IG).
OK: MIL is illuminated.Â
NG: Go to step  6
OK: SYSTEM OKÂ
- Check if the MIL is illuminated when the engine switch is turned on (IG).
- CHECK THAT ENGINE STARTSÂ
- Turn the engine switch on (IG).
- Start the engine.
ResultÂ
RESULT REFERENCEResult Proceed to Engine starts A Engine does not start* B HINT:
*: The Techstream cannot communicate with the ECM.B: GO TO VC OUTPUT CIRCUITÂ (See VC OUTPUT CIRCUITÂ )
A: Go to Next StepÂ
- CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)Â
- Disconnect the A38 ECM connector.
- Disconnect the E77 combination meter connector.
- Measure the resistance according to the value(s) in the table below.
Standard ResistanceÂ
TESTER CONNECTION SPECIFIED CONDITION CHARTTester Connection Condition Specified Condition A38-24(W) - E77-18 (CHK) Always Below 1 Ω NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK: REPLACE COMBINATION METER ASSEMBLYÂ (See REMOVAL )
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
