Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Terminals Of Ecu
- CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LHΒ
- Disconnect the I12 motor connector.
- Measure the resistance and voltage according to the value(s) in the table below.RESISTANCE AND VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I12-2 (B) - I12-1 (GND) L - W-B Battery power supply Always 11 to 14 V I12-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the I12 motor connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I12-10 (UP) - I12-1 (GND) L - W-B Power window up operation Engine switch on (IG), multiplex network master switch off β up 11 to 14 V β Below 1 V I12-10 (UP) - I12-1 (GND) L - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V I12-7 (DOWN) - I12-1 (GND) B - W-B Power window down operation Engine switch on (IG), multiplex network master switch off β down 11 to 14 V β Below 1 V I12-7 (DOWN) - I12-1 (GND) B - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the motor may be malfunctioning.
- CHECK FRONT POWER WINDOW REGULATOR MOTOR RHΒ
- Disconnect the I4 motor connector.
- Measure the resistance and voltage according to the value(s) in the table below.RESISTANCE AND VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I4-2 (B) - I4-1 (GND) L - W-B Battery power supply Always 11 to 14 V I4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the I4 motor connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I4-10 (UP) - I4-1 (GND) L - W-B Power window up operation Engine switch on (IG), power window regulator switch off β up 11 to 14 V β Below 1 V I4-10 (UP) - I4-1 (GND) L - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V I4-7 (DOWN) - I4-1 (GND) B - W-B Power window down operation Engine switch on (IG), power window regulator switch off β down 11 to 14 V β Below 1 V I4-7 (DOWN) - I4-1 (GND) B - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the motor may be malfunctioning.
- CHECK REAR POWER WINDOW REGULATOR MOTOR LHΒ
- Disconnect the J11 motor connector.
- Measure the resistance and voltage according to the value(s) in the table below.RESISTANCE AND VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J11-2 (B) - J11-1 (GND) L - W-B Battery power supply Always 11 to 14 V J11-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the J11 motor connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J11-10 (UP) - J11-1 (GND) L - W-B Power window up operation Engine switch on (IG), power window regulator switch off β up 11 to 14 V β Below 1 V J11-10 (UP) - J11-1 (GND) L - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V J11-7 (DOWN) - J11-1 (GND) B - W-B Power window down operation Engine switch on (IG), power window regulator switch off β down 11 to 14 V β Below 1 V J11-7 (DOWN) - J11-1 (GND) B - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the motor may be malfunctioning
- CHECK REAR POWER WINDOW REGULATOR MOTOR RHΒ
- Disconnect the J4 motor connector.
- Measure the resistance and voltage according to the value(s) in the table below.RESISTANCE AND VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J4-2 (B) - J4-1 (GND) L - W-B Battery power supply Always 11 to 14 V J4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the J4 motor connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J4-10 (UP) - J4-1 (GND) L - W-B Power window up operation Engine switch on (IG), power window regulator switch off β up 11 to 14 V β Below 1 V J4-10 (UP) - J4-1 (GND) L - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V J4-7 (DOWN) - J4-1 (GND) B - W-B Power window down operation Engine switch on (IG), power window regulator switch off β down 11 to 14 V β Below 1 V J4-7 (DOWN) - J4-1 (GND) B - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the motor may be malfunctioning.
- CHECK MULTIPLEX NETWORK MASTER SWITCHΒ
- Disconnect the I11 master switch connector
- Measure the resistance and voltage according to the value(s) in the table below.RESISTANCE AND VOLTAGE SPECIFICATION
Terminal No (Symbol) Wiring Color Terminal Description Condition Specified Condition I11-11 (B) - I11-12 (GND) L - W-B Battery power supply Always 11 to 14 V I11-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the I11 master switch connector
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I11-20 (UP) - I11-12 (GND) L - W-B Power window up operation Engine switch on (IG), multiplex network master switch off β up 11 to 14 V β Below 1 V I11-20 (UP) - I11-12 (GND) L - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V I11-15 (DOWN) - I11-12 (GND) B - W-B Power window down operation Engine switch on (IG), multiplex network master switch off β down 11 to 14 V β Below 1 V I11-15 (DOWN) - I11-12 (GND) B - W-B Power window down operation Engine switch ON (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the master switch may be malfunctioning.
- CHECK POWER WINDOW REGULATOR SWITCHΒ
- Disconnect the I3 switch connector.
- Measure the resistance according to the value(s) in the table below.RESISTANCE REFERENCE
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I3-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the I3 switch connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition I3-2 (UP) - I3-5 (GND) L - W-B Power window up operation Engine switch on (IG), power window regulator switch off β up 11 to 14 V β Below 1 V I3-10 (DOWN) - I3-5 (GND) B - W-B Power window down operation Engine switch on (IG), power window regulator switch off β down 11 to 14 V β Below 1 V I3-4 (AUTO) - I3-5 (GND) R - W-B Power window up operation Engine switch on (IG), and door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V I3-4 (AUTO) - I3-5 (GND) R - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the switch may be malfunctioning.
- CHECK REAR POWER WINDOW REGULATOR SWITCH LHΒ
- Disconnect the J10 switch connector.
- Measure the resistance according to the value(s) in the table below.RESISTANCE REFERENCE
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J10-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the J10 switch connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J10-2 (UP) - J10-5 (GND) L - W-B Power window up operation Engine switch on (IG), power window regulator switch off β up 11 to 14 V β Below 1 V J10-10 (DOWN) - J10-5 (GND) B - W-B Power window down operation Engine switch on (IG), power window regulator switch off β down 11 to 14 V β Below 1 V J10-4 (AUTO) - J10-5 (GND) R - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V J10-4 (AUTO) - J10-5 (GND) R - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the switch may be malfunctioning.
- CHECK REAR POWER WINDOW REGULATOR SWITCH RHΒ
- Disconnect the J3 switch connector.
- Measure the resistance according to the value(s) in the table below.RESISTANCE REFERENCE
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J3-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ© If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the J3 switch connector.
- Measure the voltage according to the value(s) in the table below.VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition J3-2 (UP) - J3-5 (GND) L - W-B Power window up operation Engine switch on (IG), power window regulator switch off β up 11 to 14 V β Below 1 V J3-10 (DOWN) - J3-5 (GND) B - W-B Power window down operation Engine switch on (IG), power window regulator switch off β down 11 to 14 V β Below 1 V J3-4 (AUTO) - J3-5 (GND) R - W-B Power window up operation Engine switch on (IG), door glass fully open β power window auto up operation β door glass fully closed 11 to 14 V β Below 1 V β 11 to 14 V J3-4 (AUTO) - J3-5 (GND) R - W-B Power window down operation Engine switch on (IG), door glass fully closed β power window auto down operation β door glass fully open 11 to 14 V β Below 1 V β 11 to 14 V If the result is not as specified, the switch may be malfunctioning.
- CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)Β
- Disconnect the 2A, 2C, E1, E2 and E3 ECU connectors.
- Measure the resistance and voltage according to value(s) in the table below.RESISTANCE AND VOLTAGE SPECIFICATION
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition E3-1 (GND3) - 2D-62 (GND2) BR - W-B Ground Always Below 1 Ξ© 2D-62 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ξ© 2A-1 (IG) - Body ground B - Body ground IG power supply Always 11 to 14 V E2-1 (AM2) - Body ground W - Body ground Battery power supply Always 11 to 14 V E1-6 (AM1) - Body ground W - Body ground Battery power supply Always 11 to 14 V E1-24 (DCTY) - Body ground L - Body ground Driver side door courtesy light switch input Driver side door open Below 1 Ξ© Driver side door closed 10 kΞ© or higher E2-21 (PCTY) - Body ground Y - Body ground Front passenger side door courtesy light switch input Front passenger side door open Below 1 Ξ© Front passenger side door closed 10 kΞ© or higher E2-7 (RCTY) - Body ground G - Body ground Rear RH side door courtesy light switch input Rear RH side door open Below 1 Ξ© Rear RH side door closed 10 kΞ© or higher 2C-2 (LCTY) - Body ground W - Body ground Rear LH side door courtesy light switch input Rear LH side door open Below 1 Ξ© Rear LH side door closed 10 kΞ© or higher If the result is not as specified, the wire harness side may have a malfunction
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
