2008 Lexus LS 460LFACTORY OEM SERVICE PROCEDURE

Terminals Of Ecu

  1. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LHΒ 
    1. Disconnect the N11 motor connector.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N11-2 (B) - N11-1 (E) O - B Battery power supply Always 11 to 14 V
      N11-1 (E) - Body ground B - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 1: Identifying Front Power Window Regulator Motor Assembly LH Connector Terminal N11
      G04952073Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the N11 motor connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N11-10 (UP1) - N11-1 (E) L - B Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      N11-10 (UP1) - N11-1 (E) L - B Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      N11-7 (DWN1) - N11-1 (E) GR - B Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      N11-7 (DWN1) - N11-1 (E) GR - B Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V

      If the result is not as specified, the motor may be malfunctioning.

  2. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RHΒ 
    1. Disconnect the N3 motor connector.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N3-2 (B) - N3-1 (E) O - B Battery power supply Always 11 to 14 V
      N3-1 (E) - Body ground B - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 2: Identifying Front Power Window Regulator Motor Assembly RH Connector N3
      G04952074Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the N3 motor connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N3-10 (UP1) - N3-1 (E) GR - B Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      N3-10 (UP1) - N3-1 (E) GR - B Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      N3-7 (DWN1) - N3-1 (E) BR - B Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      N3-7 (DWN1) - N3-1 (E) BR - B Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V

      If the result is not as specified, the motor may be malfunctioning.

  3. CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LHΒ 
    1. Disconnect the O19 motor connector.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O19-2 (B) - O19-1 (E) O - B Battery power supply Always 11 to 14 V
      O19-1 (E) - Body ground B - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 3: Identifying O19 Motor Connector
      G04952075Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the O19 motor connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O19-10 (UP1) - O19-1 (E) BR - B Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      O19-10 (UP1) - O19-1 (E) BR - B Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      O19-7 (DWN1) - O19-1 (E) Y - B Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      O19-7 (DWN1) - O19-1 (E) Y - B Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V

      If the result is not as specified, the motor may be malfunctioning.

  4. CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RHΒ 
    1. Disconnect the O8 motor connector.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O8-2 (B) - O8-1 (E) O - B Battery power supply Always 11 to 14 V
      O8-1 (E) - Body ground B - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 4: Identifying O8 Motor Connector
      G04952076Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the O8 motor connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O8-10 (UP1) - O8-1 (E) BR - B Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      O8-10 (UP1) - O8-1 (E) BR - B Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      O8-7 (DWN1) - O8-1 (E) Y - B Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      O8-7 (DWN1) - O8-1 (E) Y - B Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V

      If the result is not as specified, the motor may be malfunctioning.

  5. CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLYΒ 
    1. Disconnect the N13 master switch connector.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N13-11 (B) - N13-12 (GND) B - R Battery power supply Always 11 to 14 V
      N13-12 (GND) - Body ground R - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 5: Identifying N13 Master Switch Connector
      G04952077Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the N13 master switch connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N13-20 (UP) - N13-12 (GND) L - R Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      N13-20 (UP) - N13-12 (GND) L - R Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      N13-15 (DOWN) - N13-12 (GND) GR - R Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      N13-15 (DOWN) - N13-12 (GND) GR - R Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1V β†’ 11 to 14 V
      N13-18 (LED) - N13-12 (GND) BR - R Illuminates when power window operation permitted Engine switch off Below 1 V
      N13-18 (LED) - N13-12 (GND) BR - R Illuminates when power window operation permitted Engine switch on (IG) 11 to 14 V

      If the result is not as specified, the master switch may be malfunctioning.

  6. CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY RHΒ 
    1. Disconnect the N6 switch connector.
    2. Measure the resistance according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N6-5 (GND) - Body ground R - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 6: Identifying N6 Switch Connector
      G04952078Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the N6 switch connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N6-2 (UP) - N6-5 (GND) GR - R Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      N6-10 (DOWN) - N6-5 (GND) BR - R Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      N6-4 (AUTO) - N6-5 (GND) L - R Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1V β†’ 11 to 14 V
      N6-4 (AUTO) - N6-5 (GND) L - R Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      N6-8 (LED) - N6-5 (GND) Y - R Illuminates when power window operation permitted Engine switch off Below 1 V
      N6-8 (LED) - N6-5 (GND) Y - R Illuminates when power window operation permitted Engine switch on (IG) and window lock switch UNLOCK 11 to 14 V

      If the result is not as specified, the switch may be malfunctioning.

  7. CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LHΒ 
    1. Disconnect the O18 switch connector.
    2. Measure the resistance according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O18-5 (GND) - Body ground R - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 7: Identifying O18 Switch Connector
      G04952079Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the O18 switch connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O18-2 (UP) - O18-5 (GND) BR - R Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      O18-10 (DOWN) - O18-5 (GND) Y - R Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      O18-4 (AUTO) - O18-5 (GND) GR - R Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      O18-4 (AUTO) - O18-5 (GND) GR - R Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      O18-8 (LED) - O18-5 (GND) L - R Illuminates when power window operation permitted Engine switch off Below 1 V
      O18-8 (LED) - O18-5 (GND) L - R Illuminates when power window operation permitted Engine switch on (IG) and window lock switch UNLOCK 11 to 14 V

      If the result is not as specified, the switch may be malfunctioning.

  8. CHECK REAR WINDOW REGULATOR SWITCH ASSEMBLY RHΒ 
    1. Disconnect the O7 switch connector.
    2. Measure the resistance according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O7-5 (GND) - Body ground R - Body ground Ground Always Below 1 Ξ©

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 8: Identifying O7 Switch Connector
      G04952080Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the O7 switch connector.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O7-2 (UP) - O7-5 (GND) BR - R Power window UP operation Engine switch on (IG), switch OFF β†’ UP 11 to 14 V β†’ Below 1 V
      O7-10 (DOWN) - O7-5 (GND) Y - R Power window DOWN operation Engine switch on (IG), switch OFF β†’ DOWN 11 to 14 V β†’ Below 1 V
      O7-4 (AUTO) - O7-5 (GND) GR - R Power window UP operation Engine switch on (IG), door glass fully open β†’ power window AUTO UP operation β†’ door glass fully closed 11 to 14 V β†’ Below 1V β†’ 11 to 14 V
      O7-4 (AUTO) - O7-5 (GND) GR - R Power window DOWN operation Engine switch on (IG), door glass fully closed β†’ power window AUTO DOWN operation β†’ door glass fully open 11 to 14 V β†’ Below 1 V β†’ 11 to 14 V
      O7-8 (LED) - O7-5 (GND) L - R Illuminates when power window operation permitted Engine switch off Below 1 V
      O7-8 (LED) - O7-5 (GND) L - R Illuminates when power window operation permitted Engine switch on (IG) and window lock switch UNLOCK 11 to 14 V

      If the result is not as specified, the switch may be malfunctioning.

  9. CHECK FRONT MULTIPLEX NETWORK DOOR ECU LHΒ 
    1. Disconnect the P10 and N10 ECU connectors.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ©
      N10-11 (CPUB) - N10-1 (GND) B-W-B Battery (power supply) Always 11 to 14 V
      N10-6 (BDR) - N10-1 (GND) O-W - B Battery (power supply) Always 11 to 14 V
      N10-4 (BCUT) - N10-1 (GND) B-W - B Ignition power supply Engine switch off β†’ Engine switch on (IG) Below 1 V β†’ 11 to 14 V
      N10-3 (SIG) - N10-1 (GND) L-W - B Ignition power supply Engine switch off β†’ Engine switch on (IG) Below 1 V β†’ 11 to 14 V

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 9: Identifying P10 & N10 ECU Connectors
      G04952081Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the P10 and N10 ECU connectors.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N10-5 (BDRJ) - N10-1 (GND) O-W - B +B power output Always 11 to 14 V
      N10-2 (PWE) - Body ground B - Body ground Ground Always Below 1 V
      P10-26 (CPBJ) - N10-1 (GND) B-W - B Ignition signal output Engine switch off Below 1 V
      P10-26 (CPBJ) - N10-1 (GND) B-W - B Ignition signal output Engine switch on (IG) 11 to 14 V
      P10-27 (SGND) - Body ground R - Body ground Ground Always Below 1 V

      If the result is not as specified, the ECU may be malfunctioning.

  10. CHECK FRONT MULTIPLEX NETWORK DOOR ECU RHΒ 
    1. Disconnect the P4 and N1 ECU connectors.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ©
      N1-11 (CPUB) - N1-1 (GND) R-W - B Battery (power supply) Always 11 to 14 V
      N1-6 (BDR) - N1-1 (GND) O-W - B Battery (power supply) Always 11 to 14 V
      N1-3 (SIG) - N1-1 (GND) V-W - B Ignition power supply Engine switch off Below 1 V
      N1-3 (SIG) - N1-1 (GND) V-W - B Ignition power supply Engine switch on (IG) 11 to 14 V

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 10: Identifying P4 & N1 ECU Connectors
      G04952082Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the P4 and N1 ECU connectors.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      N1-5 (BDRJ) - N1-1 (GND) O-W - B +B power output Always 11 to 14 V
      N1-2 (PWE) - Body ground B - Body ground Ground Always Below 1 V
      P4-27 (SGND) - Body ground R - Body ground Ground Always Below 1 V

      If the result is not as specified, the ECU may be malfunctioning.

  11. CHECK REAR MULTIPLEX NETWORK DOOR ECU LHΒ 
    1. Disconnect the O15 and O14 ECU connectors.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O14-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ©
      O14-11 (CPUB) - O14-1 (GND) R-W - B Battery (power supply) Always 11 to 14 V
      O14-6 (BDR) - O14-1 (GND) L-W - B Battery (power supply) Always 11 to 14 V
      O14-3 (SIG) - O14-1 (GND) Y-W - B Ignition power supply Engine switch off Below 1 V
      O14-3 (SIG) - O14-1 (GND) Y-W - B Ignition power supply Engine switch on (IG) 11 to 14 V

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 11: Identifying O15 & O14 ECU Connectors
      G04952083Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the O15 and O14 ECU connectors.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O14-5 (BDRJ) - O14-1 (GND) 0-W - B +B power output Always 11 to 14 V
      O14-2 (PWE) - Body ground B - Body ground Ground Always Below 1 V
      O15-25 (SGND) - Body ground R - Body ground Ground Always Below 1 V

      If the result is not as specified, the ECU may be malfunctioning.

  12. CHECK REAR MULTIPLEX NETWORK DOOR ECU RHΒ 
    1. Disconnect the O2 and O3 ECU connectors.
    2. Measure the resistance and voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ξ©
      O3-11 (CPUB) - O3-1 (GND) R-W - B Battery (power supply) Always 11 to 14 V
      O3-6 (BDR) - O3-1 (GND) L-W - B Battery (power supply) Always 11 to 14 V
      O3-3 (SIG) - O3-1 (GND) Y-W - B Ignition power supply Engine switch off Below 1 V
      O3-3 (SIG) - O3-1 (GND) Y-W - B Ignition power supply Engine switch on (IG) 11 to 14 V

      If the result is not as specified, there may be a malfunction on the wire harness side.

      Fig 12: Identifying O2 & O3 ECU Connectors
      G04952084Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the O2 and O3 ECU connectors.
    4. Measure the voltage according to the value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      O3-5 (BDRJ) - O3-1 (GND) O-W - B +B power output Always 11 to 14 V
      O3-2 (PWE) - Body ground B - Body ground Ground Always Below 1 V
      O2-25 (SGND) - Body ground R - Body ground Ground Always Below 1 V

      If the result is not as specified, the ECU may be malfunctioning.

  13. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)Β 
    1. Disconnect the DA, DD, DF, L11, L12 and L13 ECU connectors.
    2. Measure the resistance and voltage according to value(s) in the table below.
      CONNECTOR TERMINAL REFERENCE TABLE

      Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
      L11-1 (GND3) - DA-41 (GND1) W-B - W - B Ground Always Below 1 Ξ©
      DA-40 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ξ©
      DA-40 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ξ©
      DF-1 (ALTB) - Body ground B - Body ground IG power supply Always 11 to 14 V
      L12-1 (AM2) - Body ground W - Body ground Battery power supply Always 11 to 14 V
      L13-6 (AM1) - Body ground W - Body ground Battery power supply Always 11 to 14 V
      L13-24 (DCTY) - Body ground W - Body ground Driver side door courtesy light switch input Driver side door is open Below 1 Ξ©
      Driver side door is closed 10 kΞ© or higher
      L12-21 (PCTY) - Body ground L - Body ground Front passenger side door courtesy light switch input Front passenger side door is open Below 1 Ξ©
      Front passenger side door is closed 10 kΞ© or higher
      L12-7 (RCTY) - Body ground R - Body ground Rear RH side door courtesy light switch input Rear RH side door is open Below 1 Ξ©
      Rear RH side door is closed 10 kΞ© or higher
      DD-12 (LCTY) - Body ground L - Body ground Rear LH side door courtesy light switch input Rear LH side door is open Below 1 Ξ©
      Rear LH side door is closed 10 kΞ© or higher

      If the result is not as specified, the wire harness side may have a malfunction.

      Fig 13: Identifying DA, DD, DF, L11, L12 & L13 ECU Connectors
      G04943821Courtesy of Β© TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.