Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK CAN COMMUNICATION SYSTEMÂ
- Check if a CAN communication system DTC is output (See
DIAGNOSIS SYSTEM
).
ResultÂ
RESULT REFERENCEResult Proceed to DTC is not output A DTC is output B
B: INSPECT CAN COMMUNICATION SYSTEMÂ (See HOW TO PROCEED WITH TROUBLESHOOTING )
A: Go to next stepÂ
- Check if a CAN communication system DTC is output (See
DIAGNOSIS SYSTEM
).
- CHECK MULTIPLEX COMMUNICATION SYSTEMÂ
- Check if a multiplex communication system DTC is output (See
DIAGNOSTIC TROUBLE CODE CHART
)
ResultÂ
RESULT REFERENCEResult Proceed to DTC is not output A DTC is output B
B: INSPECT MULTIPLEX COMMUNICATION SYSTEMÂ (See DIAGNOSTIC TROUBLE CODE CHART )
A: Go to next stepÂ
- Check if a multiplex communication system DTC is output (See
DIAGNOSTIC TROUBLE CODE CHART
)
- CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTEDÂ
- Check if the skid control ECU connector is securely connected.
OK: The connector is securely connected.Â
NG: CONNECT CONNECTOR TO ECU CORRECTLYÂ (See ELECTRONIC CIRCUIT INSPECTION PROCEDURE )
OK: Go to next stepÂ
- Check if the skid control ECU connector is securely connected.
- CHECK BATTERYÂ
- Check the battery voltage.
Standard Voltage:Â
11 to 14 VÂ
NG: CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (for 2UR-GSE)Â (See ON-VEHICLE INSPECTION )
OK: Go to next stepÂ
- Check the battery voltage.
- READ VALUE USING TECHSTREAM (VSC OFF SWITCH)Â
- Connect the Techstream to the DLC3
- Turn the engine switch on (IG).
- Select the Data List mode on the Techstream (See DATA LIST / ACTIVE TESTÂ
)
ABS/VSC/TRACÂ
NORMAL CONDITIONTester Display Measurement Item / Range Normal Condition Diagnostic Note TRAC/VSC Off Mode VSC OFF switch / NORMAL, TRC OFF or VSC OFF NORMAL Normal mode
TRC OFF TRAC off mode
VSC OFF VSC off mode- - Using the Techstream, check the switch condition on the Techstream changes according to VSC OFF switch operation
OK: The Techstream display changes according to VSC OFF switch operation.Â
NG: Go to step  7
OK: Go to next stepÂ
- INSPECT COMBINATION METER ASSEMBLYÂ
- Turn the engine switch off
- Perform the Active Test of the combination meter (meter CPU) using the Techstream (See DATA LIST / ACTIVE TEST )
- Check the combination meter
OK: The slip indicator light turns on or off in accordance with the Techstream operation.Â
HINT
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See PROBLEM SYMPTOMS TABLEÂ )
NG: REPLACE COMBINATION METER ASSEMBLYÂ (See REMOVAL )
OK: REPLACE SKID CONTROL ECUÂ (See REMOVALÂ )
- INSPECT VSC OFF SWITCHÂ
- Turn the engine switch off
- Disconnect the VSC OFF switch connector
- Measure the resistance according to the value(s) in the table below
Standard ResistanceÂ
STANDARD RESISTANCETester Connection Switch Condition Specified Condition 3 (+) - 4 (E) Switch is not pushed in 10 kΩ or higher
NG: REPLACE VSC OFF SWITCHÂ (See REMOVALÂ )
OK: Go to next stepÂ
- CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)Â
- Disconnect the skid control ECU connector.
- Measure the resistance according to the value(s) in the table below
Standard ResistanceÂ
STANDARD RESISTANCETester Connection Condition Specified Condition J77-7 (CSW) - J37-3 (+) Always Below 1 Ω J77-7 (CSW) - Body ground Always 10 kΩ or higher J37-4 (E) - Body ground Always Below 1 Ω HINT.
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See PROBLEM SYMPTOMS TABLEÂ ).
NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
OK: REPLACE SKID CONTROL ECUÂ (See REMOVALÂ )
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
