Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Terminals Of Ecu
- CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
- Disconnect the P33 ECU connector
- Measure the voltage and resistance according to the value(s) in the table belowVOLTAGE SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition P33-1 (+B1) - P33-17 (E) L - W-B Battery power supply Always 11 to 14 V P33-17(E) - Body ground W-B - Body ground Ground Always Below 1 Ω If the result is not as specified, there may be a malfunction on the wire harness side
- Reconnect the P33 ECU connector
- Measure the voltage and pulse according to the value(s) in the table belowVOLTAGE SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition P33-18(IG) - P33-17(E) B - W-B Engine switch power supply Engine switch on (IG) 11 to 14 V P33-18(IG) - P33-17(E) B - W-B Engine switch power supply Engine switch off Below 1 V P33-10(LIN) - P33-17(E) V - W-B LIN Communication line Engine switch on (IG) Pulse generation If the result is not as specified, the ECU may be malfunctioning
- CHECK POWER SOURCE CONTROL ECU
- Disconnect the J55 ECU connector
- Measure the resistance and voltage according to the value(s) in the table belowVOLTAGE AND RESISTANCE SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition J55-6 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω J55-12(AM2) - Body ground O - Body ground +B power supply Always 11 to 14 V J55-33(AM1) - Body ground O - Body ground +B power supply Always 11 to 14 V If the result is not as specified, there may be a malfunction on the wire harness side
- Reconnect the J55 ECU connector
- Measure the pulse according to the value(s) in the table belowTESTER CONNECTION SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition J55-30 (LIN1) - J55-6 (GND2) V - W-B LIN Communication line Engine switch on (IG) Pulse generation If the result is not as specified, the ECU may be malfunctioning.
- CHECK ID CODE BOX (IMMOBILIZER CODE ECU)
- Disconnect the J69 ECU connector.
- Measure the voltage and resistance according to the value(s) in the table below.VOLTAGE AND RESISTANCE SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition J69-1 (+B) - J69-8 (GND) G - W-B Battery power supply Always 11 to 14 V J69-8 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω If the result is not as specified, there may be a malfunction on the wire harness side
- Reconnect the J69 ECU connector.
- Measure the pulse according to the value(s) in the table belowTESTER CONNECTION SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition J69-3 (LIN1) - J69-8 (GND) V - W-B LIN Communication line Engine switch on (IG) Pulse generation If the result is not as specified, the ECU may be malfunctioning.
- CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
- Disconnect the J29 ECU connector.
- Measure the voltage and resistance according to the value(s) in the table below.VOLTAGE AND RESISTANCE SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition J29-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω J29-6 (IG2) - J29-1 (GND) LG - W-B Engine switch power supply Engine switch on (IG) 11 to 14 V J29-6 (IG2) - J29-1 (GND) LG - W-B Engine switch power supply Engine switch off Below 1 V J29-7 (B) - J29-1 (GND) O - W-B Battery power supply Always 11 to 14 V If the result is not as specified, there may be a malfunction on the wire harness side
- Reconnect the J29 ECU connector
- Measure the pulse according to the value(s) in the table belowTESTER CONNECTION SPECIFICATION
Tester Connection Wiring Color Terminal Description Condition Specified Condition J29-5 (LIN) - J29-1 (GND) V - W-B LIN Communication line Engine switch on (IG) Pulse generation If the result is not as specified, the ECU may be malfunctioning
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
