Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Lexus GX 470FACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Chart
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the "Refer to" given.
HINT:
- *1: "Comes on" means the MIL (Malfunction Indicator Lamp) illuminates.
- *2: "DTC stored" means the ECM memorizes the malfunction code when the ECM detects the DTC detection condition.
- These DTCs may be output when the clutch, brake, gear components, etc. inside the automatic transmission are damaged.
AUTOMATIC TRANSMISSION SYSTEM:
DTC CODE CHART
| DTC Code | Detection Item | Trouble Area | MIL*1 | Memory *2 |
|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
|
Comes on | DTC stored |
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit |
|
Comes on | DTC stored |
| P0711 | Transmission Fluid Temperature Sensor "A" Performance | Transmission wire (No 1 ATF temperature sensor) | Comes on | DTC stored |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low Input |
|
Comes on | DTC stored |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High Input |
|
Comes on | DTC stored |
| P0717 | Turbine Speed Sensor Circuit No Signal |
|
Comes on | DTC stored |
| P0722 | Output Speed Sensor Circuit No Signal |
|
Comes on | DTC stored |
| P0724 | Brake Switch "B" Circuit High |
|
Comes on | DTC stored |
| P0746 | Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) |
|
Comes on | DTC stored |
| P0748 | Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) |
|
Comes on | DTC stored |
| P0751 | Shift Solenoid "A" Performance (Shift Solenoid Valve S1) |
|
Comes on | DTC stored |
| P0756 | Shift Solenoid "B" Performance (Shift Solenoid Valve S2) |
|
Comes on | DTC stored |
| P0771 | Shift Solenoid "E" Performance (Shift Solenoid Valve SR) |
|
Comes on | DTC stored |
| P0776 | Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) |
|
Comes on | DTC stored |
| P0778 | Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) |
|
Comes on | DTC stored |
| P0781 | 1-2 Shift (1-2 Shift Valve) |
|
Comes on | DTC stored |
| P0818 | Driveline Disconnect Switch Input Circuit |
|
Comes on | DTC stored |
| P0894 | Transmission Component Slipping |
|
Comes on | DTC stored |
| P0973 | Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1) |
|
Comes on | DTC stored |
| P0974 | Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1) |
|
Comes on | DTC stored |
| P0976 | Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) |
|
Comes on | DTC stored |
| P0977 | Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2) |
|
Comes on | DTC stored |
| P0985 | Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR) |
|
Comes on | DTC stored |
| P0986 | Shift Solenoid "E" Control Circuit High (Shift Solenoid Valve SR) |
|
Comes on | DTC stored |
| P2714 | Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |
|
Comes on | DTC stored |
| P2716 | Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) |
|
Comes on | DTC stored |
| P2740 | Transmission Fluid Temperature Sensor "B" Circuit |
|
Comes on | DTC stored |
| P2742 | Transmission Fluid Temperature Sensor "B" Circuit Low Input |
|
Comes on | DTC stored |
| P2743 | Transmission Fluid Temperature Sensor "B" Circuit High Input |
|
Comes on | DTC stored |
| P2757 | Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |
|
Comes on | DTC stored |
| P2759 | Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) |
|
Comes on | DTC stored |
| P2772 | Four Wheel Drive (4WD) Low Switch Circuit Range / Performance |
|
Comes on | DTC stored |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
