Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK MILÂ
- Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.
OK: MIL lights upÂ
OK: SYSTEM OKÂ
NG: Go to Next StepÂ
- Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.
- CHECK CONNECTION BETWEEN TECHSTREAM AND ECMÂ
- Connect the Techstream to the DLC3.
- Turn the ignition switch ON and tester ON.
- Check the communication between the Techstream and ECM.
ResultÂ
RESULT REFERENCECondition Proceed to Communication is possible A Communication is impossible B
A: GO TOÂ MIL CIRCUITÂ
B: Go to Next StepÂ
- INSPECT ECMÂ
- Turn the ignition switch ON.
- Measure the voltage between E5-23 (VC) and E7-1 (E1) of the ECM connectors.
Standard voltage:Â
Voltage is not 5 VÂ
- CHECK MIL (THROTTLE POSITION SENSOR)Â
- Disconnect the T2 throttle body connector.
- Turn the ignition switch ON.
- Check the MIL.
ResultÂ
RESULT REFERENCECondition Proceed to MIL illuminates A MIL does not illuminate B
A: REPLACE THROTTLE BODYÂ
B: Go to Next StepÂ
- CHECK MIL (CAMSHAFT POSITION SENSOR)Â
- Disconnect the C1 camshaft position sensor connector.
- Turn the ignition switch ON.
- Check the MIL
ResultÂ
RESULT REFERENCECondition Proceed to MIL illuminates A MIL does not illuminate B
A: REPLACE CAMSHAFT POSITION SENSORÂ
B: Go to Next StepÂ
- CHECK MIL (CANISTER PUMP MODULE)Â
- Remove the spare tire.
- Disconnect the L4 canister pump module connector.
- Turn the ignition switch ON
- Check the MIL.
ResultÂ
RESULT REFERENCECondition Proceed to MIL illuminates A MIL does not illuminate B
A: REPLACE CANISTERÂ
B: Go to Next StepÂ
- CHECK MIL (PRESSURE SENSOR)Â
- Remove the intake manifold (see REMOVAL ).
- Disconnect the A45 pressure sensor connector.
- Turn the ignition switch ON.
- Check the MIL
ResultÂ
RESULT REFERENCECondition Proceed to MIL illuminates A MIL does not illuminate B
A: REPLACE AIR PRESSURE SENSORÂ
B: Go to Next StepÂ
- CHECK HARNESS AND CONNECTORÂ
- Disconnect the T2 throttle body connector.
- Disconnect the C1 camshaft position sensor connector
- Disconnect the L4 canister pump module connector.
- Disconnect the A45 pressure sensor.
- Disconnect the E5 ECM connector.
- Measure the resistance of the wire harness side connector.
Standard resistance (check for short)Â
STANDARD VOLTAGETester Connection Specified Condition VC (E5-23) - Body ground 10 kΩ or higher
NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
OK: REPLACE ECMÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
