Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
- Disconnect the transmission control switch connector of the shift lever assembly.
- Measure the voltage according to the value (s) in the table below.
Standard Voltage
STANDARD VOLTAGE SPECIFICATIONTester Connection Switch Condition Specified Condition 3 - Body ground Engine switch on (IG) 11 to 14 V Engine switch off Below 1 V
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
- Measure the resistance according to the value (s) in the table below.
Standard Resistance
STANDARD RESISTANCE SPECIFICATIONTester Connection Condition Specified Condition 5 - Body ground Always Below 1 Ω
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- Measure the resistance according to the value (s) in the table below.
- INSPECT TRANSMISSION CONTROL SWITCH
- Measure the resistance between each terminal of the shift lever assembly when the shift lever is moved to each position.
Standard Resistance
STANDARD RESISTANCE SPECIFICATIONTester Connection Shift Position Specified Condition 3 - 7 S, "+" and "-" Below 1 Ω Except S, "+" and "-" 10 kΩ or higher 2 - 5 Press continuously "+" (Up shift) Below 1 Ω S 10 kΩ or higher 1 - 5 Press continuously (Down shift) Below 1 Ω S 10 kΩ or higher
NG: REPLACE TRANSMISSION CONTROL SWITCH
OK: Go to next step
- Measure the resistance between each terminal of the shift lever assembly when the shift lever is moved to each position.
- CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
- Connect the transmission control switch connector of the shift lever assembly.
- Disconnect the A10 ECM connector.
- Turn the engine switch on (IG), and measure the voltage according to the value (s) in the table below when the shift lever is moved to each position.
Standard Voltage
STANDARD VOLTAGE SPECIFICATIONTester Connection Shift Position Specified Condition A10-25 (S) - Body ground S, "+" and "-" 11 to 14 V Except S, "+" and "-" Below 1 V - Turn the engine switch off.
- Disconnect the ECM connector.
- Measure the resistance according to the value (s) in the table below when the shift lever is moved to each position.
Standard Resistance
STANDARD RESISTANCE SPECIFICATIONTester Connection Shift Position Specified Condition A10-16 (SFTU) - Body ground Press continuously "+" (Up shift) Below 1 Ω S 10 kΩ or higher A10-51 (SFTD) - Body ground Press continuously (Down shift) Below 1 Ω S 10 kΩ or higher
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.