2008 Lexus ES 350 V6-3.5L (2GR-FE)FACTORY OEM SERVICE PROCEDURE

Smart Access System With Push-Button Start








DOOR LOCK: SMART ACCESS SYSTEM WITH PUSH-BUTTON START: CUSTOMIZE PARAMETERS

CUSTOMIZE PARAMETERS

1. CUSTOMIZING FUNCTION WITH TECHSTREAM
HINT: The items in the table below can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current setting before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.

(a) Connect Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the tester on.
(d) Enter the following menus: Customize Setting / Smart Key/Smart Access.
(e) Select the setting by referring to the table below.

Smart:

Factory service manual diagram




Wireless Door Lock:

Factory service manual diagram




Warning:

Factory service manual diagram




2. ENTRY UNLOCK MODE SWITCHING FUNCTION
(a) To change the vehicle to entry unlock mode switching function, make sure the vehicle power is off and simultaneously press and hold the electrical key's LOCK switch and another electrical key switch for 4.5 seconds.
- When the switches are pressed and held for 4.5 seconds, the entry door unlock mode changes in the following order: driver door mode, all door mode.
NOTE: After pressing and holding the switches for 4.5 seconds, wait 4.5 seconds before performing the same procedure again.
- Driver door unlock mode:
When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
- All door unlock mode:
When the touch sensor is touched, all doors unlock.

(b) The certification ECU receives this signal from the entry door control receiver and changes the smart access system with push-button start to the entry unlock mode.
(c) The certification ECU sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been switched.

Factory service manual diagram




HINT: The function only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.

3. ELECTRICAL KEY CANCEL
The electrical key cancel operation disables the following functions:

- Entry Ignition
- Entry Unlock/Lock
- Entry Luggage Compartment Open
- Electrical Key Lock-in Prevention
- Warning
- Memory Call

(a) The operation procedures are as follows:
Precondition:
Engine switch off, driver side door closed and unlocked.
(1) Unlock the driver side door once with the UNLOCK switch of the electrical key.
(2) Open the driver door within 5 seconds.
(3) Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.
(4) ->Repeat open close twice for the driver door within 30 seconds, and open again.
(Driver door: Open -> Close -> Open -> Close -> Open)
(5) Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.
(6) ->Repeat open close once for the driver door within 30 seconds, and open again.
(Driver door: Open -> Close -> Open)
(7) Close the driver door within 5 seconds.
When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.