Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Lexus SC 430FACTORY OEM SERVICE PROCEDURE
Technical Service Bulletins
- A/C Compressor
- Accessories & Equipment
- Accessories Control Systems
- Immobilizer And Smart Key Reset (SS002-01)
- Power System Initialization During PDS (PD007-07)
- TECHSTREAM Ecu Flash Reprogramming Procedure (SS002-07)
- Tire Pressure Warning Valve/Sensor Activation (PD064-06)
- DCC Fuse Installation During PDS (PD035-06)
- Initial Calibration Of Compass During PDS (PD037-06)
- Initialization Of Front Seat Position & Seatback Angle (PD036-06)
- Air Bag, SRS
- Anti-Theft Systems
- Automatic Trans
- Interior Electrical Component Precautions (L-SB-0066-11 REV2)
- ATM Manual Shift Lever/Park Neutral Position Switch Installation (L-SB-0030-11 REV1)
- Automatic Transmission Replacement Precautions (L-SB-0082-14)
- Torque Converter Bolt Installation (L-SB-0007-11 REV1)
- Remanufactured Automatic Transmission Serial Number Location (TC010-06)
- World Standard Automatic Transmission Fluid (TC008-07)
- Automatic Transmission Serial Number Location (TC009-06)
- Mil "On" DTC P0751 (L-SB-0150-09)
- Automatic Transmission/Transaxle Fluid Level Inspection Temperature Ranges (L-SB-0023-09)
- Special Service Tools (L-SB-0119-08)
- Alignment Pin Installation During Transmission/Transaxle Assembly Installation (L-SB-0026-08)
- Automatic Transmission Shipping Bag For Warranty Recovery (TC010-07)
- Axle Shafts
- Battery Management Systems
- Body Electrical
- Body Interior
- Brakes Control Systems
- Charging Systems
- Cooling System (Mechanical)
- Cruise Control Systems
- Differentials & Drive Axles
- Driveshaft & Universal Joints
- Engine Control Systems
- Entertainment Systems
- Exterior Body Panels
- Frames, Subframes & Crossmembers
- Front Suspension
- Fuses & Circuit Breakers
- General Servicing
- Headlights
- HVAC Control Systems
- Identification
- Replacement Certification Labels And VIN Plates (PG008-07)
- Remanufactured Automatic Transmission Serial Number Location (TC010-06)
- Automatic Transmission Serial Number Location (TC009-06)
- Engine Bank 1 And Bank 2 A/F And O2 Identification (L-SB-0188-09)
- Replacement Certification Labels And VIN Plates - Crib # 164 (S-CRIB-164)
- Engine Serial Number Location (L-SB-0085-08 REV1)
- Replacement VIN Plates (PG007-07)
- Ignition Switch/Steering Lock
- Infotainment
- Interior/Exterior Trim
- Lubrication System
- Mechanical
- Mechanical - Hydraulic
- Memory Modules
- Paint & Coatings
- Iron Particle Rust Contamination Repair (L-SB-0020-24)
- New Vehicle Washing Schedule For Paint Protection (L-SB-0024-24)
- Prevention And Repair Of Acid Rain Damage (L-SB-0022-24)
- PAINTLESS Dent Repair - Crib # 146 (T-CRIB-146)
- Long Term Vehicle Storage Guidelines (L-SB-0018-09 REV2)
- Plastic Bumper Refinishing - Crib # 170 (L-CRIB-170)
- Permanent-Type Protective Wax Coatings (L-SB-0083-08)
- Acid Rain Paint Finish Damage - Prevention & Repair - Crib # 165 (S-CRIB-165)
- Exterior Color And Scratch Resistant And Anti-Acid Paint (PA001-07)
- Parking Brake System
- Passive Restraints
- Procedures
- Rear Suspension
- Restraints Control Systems
- Seats
- Starter
- Steering Column
- Steering Control Systems
- Steering Linkage
- Suspension Control Systems
- System
- Transmission Control Systems
- Warning Systems
- Wheel Alignment
- Wheels & Tire System
- Tire Inflation Pressure Compensation And Adjustment (L-SB-0154-08 REV2)
- Long Term Vehicle Storage Guidelines (L-SB-0018-09 REV2)
- Tire Pressure Monitoring System (TPMS) Tire Registration And "Lost Communication With Ecu" (L-SB-0025-09)
- Tire Positioning Before New Vehicle Delivery (PG002-05)
- Direct-Type Tire Pressure Warning System Diagnostic Tips (PG001-07)
- Repair Evaluation Criteria On Run Flat Tires (PG006-02)
- Tire Pressure Warning Valve/Sensor Activation (PD064-06)
- Window Motors & Regulators
- Wiper/Washer Systems
- Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.