Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Data List / Active Test
- READ DATA LIST
HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch ON.
- Read the DATA LIST.
Multiplex network door ECU front LH (Driver door ECU): (Switch condition)
ITEM MEASUREMENT NORMAL CONDITION CHARTItem Measurement Item / Display (Range) Normal Condition Diagnostic Note P/W AUTO SW Driver side power window AUTO operation ON / OFF ON: Driver door power window
AUTO switch operates
OFF: Driver door power window
AUTO switch does not operate- P/W AUTO SW Passenger side power window AUTO operation ON / OFF ON: Passenger door remote power window AUTO switch operates
OFF: Passenger door remote power window AUTO switch does not operate- LIMIT SW Jam protection limit switch ON / OFF ON: Jam protection limit switch operates
OFF: Jam protection limit switch does not operate- Multiplex network door ECU front LH (Driver door ECU): (Glass position)
ITEM MEASUREMENT NORMAL CONDITION CHARTItem Measurement Item / Display (Range) Normal Condition Diagnostic Note GLASS POS - 1/4 Glass position (Fully closed - 1/4 open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- GLASS POS - 2/4 Glass position (1/4 open - 2/4 open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- GLASS POS - 3/4 Glass position (2/4 open - 3/4 open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- GLASS POS - OPEN Glass position (3/4 open - Fully open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- Multiplex network door ECU front RH (Passenger door ECU): (Switch condition)
ITEM MEASUREMENT NORMAL CONDITION CHARTItem Measurement Item / Display (Range) Normal Condition Diagnostic Note P/W AUTO SW Passenger side power window AUTO operation ON / OFF ON: Passenger door power window AUTO switch operates
OFF: Passenger door power window AUTO switch does not operate- LIMIT SW Jam protection limit switch ON / OFF ON: Jam protection limit switch operates
OFF: Jam protection limit switch does not operate- Multiplex network door ECU front RH (Passenger door ECU): (Glass position)
ITEM MEASUREMENT NORMAL CONDITION CHARTItem Measurement Item / Display (Range) Normal Condition Diagnostic Note GLASS POS - 1/4 Glass position (Fully closed - 1/4 open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- GLASS POS - 2/4 Glass position (1/4 open - 2/4 open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- GLASS POS - 3/4 Glass position (2/4 open - 3/4 open) OK / CAUTION OK: Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position- GLASS POS - OPEN Glass position (3/4 open - Fully open) OK / CAUTION OK; Power window is moving UP by manual operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position-
- PERFORM ACTIVE TEST CAUTION: This test causes vehicle parts to move. Please watch your hands.
HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch ON.
- Performing the ACTIVE TEST by following the directions on the tester screen.
Multiplex network door ECU front LH (Driver door ECU)
DISPLAY CONDITION CHARTItem Test Details Diagnostic Note P/W UP/DOWN Power Window UP/DOWN - Multiplex network door ECU front RH (Passenger door ECU)
ITEM CONTENT REFERENCE CHARTItem Test Details Diagnostic Note P/W UP/DOWN Power Window UP/DOWN -
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.