Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- INSPECT ECM (+B VOLTAGE)Â
- Turn the ignition switch to the ON position.
- Measure the voltage between the terminals of the E5 and E7 ECM connectors.
Standard voltageÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition +B (E5-1) - E1 (E7-1) 9 to 14 V
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLEÂ
NG: Go to Next StepÂ
- CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)Â
- Disconnect the E7 ECM connector.
- Measure the resistance between the terminal of the ECM connector and body ground.
Standard resistance:Â
Check for openÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition E1 (E7-1) - Body ground Below 1 Ω - Reconnect the ECM connector.
NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
OK: Go to Next StepÂ
- INSPECT ECM (IGSW VOLTAGE)Â
- Turn the ignition switch to the ON position.
- Measure the voltage between the terminals of the E5 and E7 ECM connectors.
Standard voltageÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition IGSW (E5-9) - E1 (E7-1) 9 to 14 V
OK: Go to step  6
NG: Go to Next StepÂ
- CHECK FUSE (IGN FUSE)Â
- Remove the IGN fuse from the instrument panel J/B.
- Measure the IGN fuse resistance.
Standard resistance:Â
Below 1 ΩÂ
- Reinstall the IGN fuse.
NG: CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSEÂ
OK: Go to Next StepÂ
- INSPECT IGNITION OR STARTER SWITCH ASSEMBLYÂ
- Inspect the ignition or starter switch assembly (See INSPECTION ).
NG: REPLACE IGNITION OR STARTER SWITCH ASSEMBLYÂ (See REMOVAL )
OK: Go to Next StepÂ
- INSPECT ECM (MREL VOLTAGE)Â
- Turn the ignition switch to the ON position.
- Measure the voltage between the terminals of the E5 and E7 ECM connectors.
Standard voltageÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition MREL (E5-8) - E1 (E7-1) 9 to 14 V
NG: REPLACE ECMÂ (See REMOVALÂ )
OK: Go to Next StepÂ
- CHECK FUSE (EFI FUSE)Â
- Remove the EFI No. 1 fuse from the fusible link block.
- Measure the EFI No. 1 fuse resistance.
Standard resistance:Â
Below 1 ΩÂ
- Reinstall the EFI No. 1 fuse.
NG: CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSEÂ
OK: Go to Next StepÂ
- INSPECT EFI MAIN RELAYÂ
- Remove the EFI MAIN relay from the fusible link block.
- Measure the EFI MAIN relay resistance.
Standard resistanceÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω (when battery voltage applied to terminals 1 and 2) - Reinstall the EFI MAIN relay.
NG: REPLACE EFI MAIN RELAYÂ
OK: Go to Next StepÂ
- CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM, EFI MAIN RELAY - BODY GROUND)Â
- Check the harness and connector between the EFI MAIN relay and ECM.
- Remove the EFI MAIN relay from the engine room R/B.
- Disconnect the E5 ECM connector.
- Measure the resistance between the terminals.
Standard resistance:Â
Check for openÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition EFI MAIN relay terminal (1) - MREL (E5-8) Below 1 Ω Check for shortÂ
TESTER CONNECTION SPECIFIED CONDITIONTester Connection Specified Condition EFI MAIN relay terminal (1) or MREL (E5-8) - Body ground 10 kΩ or higher
- Check the harness and connector between the EFI MAIN relay and body ground.
OK: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NG: CHECK AND REPLACE HARNESS AND CONNECTOR (TERMINAL +B OF ECM - BATTERY POSITIVE TERMINAL)Â
- Check the harness and connector between the EFI MAIN relay and ECM.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
