Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK OPERATION OF ENGINE CRANKINGÂ
- When turning the ignition switch to the START position check if the starter motor starts.
OK: CHECK FOR INTERMITTENT PROBLEMSÂ
NG: Go to next stepÂ
- READ VALUE OF INTELLIGENT TESTER (STA SIGNAL)Â
- Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.
- Enter the following menu: DIAGNOSIS / ENHANCED OBDII / DATA LIST / PRIMARY / STARTER SIG.
- Confirm the starter signal status when the ignition switch is operated.
OKÂ
IGNITION SWITCH POSITION AND STARTER SIGNALS REFERENCEIgnition Switch Position STARTER SIG ON OFF Start ON
OK: Go to step  5
NG: Go to next stepÂ
- INSPECT ECM (STA AND STSW VOLTAGE)Â
- Measure the voltage of the E6 ECM connector while cranking the engine (ignition switch is in the START position).
Standard voltageÂ
VOLTAGE SPECIFICATIONTester Connection Specified Condition E6-11 (STA) - E6-1 (E1) 9 to 14 V E6-12 (STSW) - E6-1 (E1) 9 to 14 V ResultÂ
RESULT REFERENCETerminal STSW Terminal STA Proceed to 9 to 14 V 9 to 14 V A 9 to 14 V 0 V B 0 V 0 V C
B: REPLACE ECMÂ
C: Go to step  9
A: Go to next stepÂ
- Measure the voltage of the E6 ECM connector while cranking the engine (ignition switch is in the START position).
- INSPECT PARK / NEUTRAL POSITION SWITCHÂ
- Disconnect the P1 park / neutral position switch connector.
- Measure the resistance between each terminal shown below when the shift lever is moved to each position.
Standard resistanceÂ
RESISTANCE SPECIFICATIONShift Position Tester Connection Specified Condition P or N 4 - 5 Below 1 Ω - Reconnect the park / neutral position switch connector.
NG: REPLACE PARK / NEUTRAL POSITION SWITCHÂ
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK: CHECK AND REPAIR HARNESS OR CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)Â
- INSPECT STARTER RELAYÂ
- Remove the starter relay from the engine room relay block.
- Measure the resistance of the starter relay.
Standard resistanceÂ
RESISTANCE SPECIFICATIONTester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω (when battery voltage applied to terminals 1 and 2) - Reinstall the starter relay.
NG: REPLACE STARTER RELAYÂ
OK: Go to next stepÂ
- CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - STARTER RELAY, STARTER RELAY - BODY GROUND)Â
- Check harness and connector (see ELECTRONIC CIRCUIT INSPECTION PROCEDURE ).
NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
OK: Go to next stepÂ
- INSPECT ENGINE ROOM RELAY BLOCK (STARTER RELAY VOLTAGE)Â
- Remove the STARTER relay from the engine room relay block.
- Measure the voltage of the engine room relay block and body ground.
Standard voltageÂ
VOLTAGE SPECIFICATIONTester Connection Specified Condition Engine room relay block (Starter relay terminal 5) - Body ground 9 to 14 V - Reinstall the STARTER relay.
NG: CHECK AND REPAIR HARNESS AND CONNECTOR (STARTER RELAY - BATTERY)Â
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK: Go to next stepÂ
- INSPECT STARTER ASSEMBLYÂ
- Inspect starter assembly (see INSPECTION ).
NG: REPAIR OR REPLACE STARTER ASSEMBLYÂ
OK: CHECK AND REPAIR HARNESS OR CONNECTOR (STARTER RELAY - STARTER, STARTER - BATTERY)Â
- INSPECT IGNITION SWITCH ASSEMBLYÂ
- Disconnect the I18 ignition switch connector.
- Measure the resistance of the connector terminals shown in the chart below.
Standard resistanceÂ
RESISTANCE SPECIFICATIONSwitch Position Tester Connection Specified Condition START 7 - 8 Below 1 Ω - Reconnect the I18 ignition switch connector.
NG: REPLACE IGNITION SWITCH ASSEMBLYÂ
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK: CHECK AND REPAIR HARNESS OR CONNECTOR (ECM - IGNITION SWITCH, IGNITION SWITCH - BATTERY)Â
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
