Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Problem Symptoms Table
HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
| Symptom | Suspected Area | See |
|---|---|---|
| Engine does not crank (Does not start) | 1. Cranking holding function circuit | CRANKING HOLDING FUNCTION CIRCUIT |
| 2. Starter | INSPECTION | |
| 3. Starter relay | ON-VEHICLE INSPECTION | |
| 4. VC output circuit | VC OUTPUT CIRCUIT | |
| No initial combustion (Does not start) | 1. ECM power source circuit | ECM POWER SOURCE CIRCUIT |
| 2. VC output circuit | VC OUTPUT CIRCUIT | |
| 3. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT | |
| 4. ECM | ECM | |
| No complete combustion | 1. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT |
| Difficult to start (Engine cranks normally) | 1. Starter signal circuit | DTC P0617 Starter Relay Circuit High |
| 2. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT | |
| 3. Compression | ON-VEHICLE INSPECTION | |
| Difficult to start (With cold engine) | 1. Starter signal circuit | DTC P0617 Starter Relay Circuit High |
| 2. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT | |
| Difficult to start (With hot engine) | 1. Starter signal circuit | DTC P0617 Starter Relay Circuit High |
| 2. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT | |
| High engine idlie speed (Poor idling) | 1. A/C signal circuit (Comoressor circuit) | COMPRESSOR CIRCUIT |
| 2. ECM power source circuit | ECM POWER SOURCE CIRCUIT | |
| Low engine idlie speed (Poor idling) | 1. A/C signal circuit (Comoressor circuit) | COMPRESSOR CIRCUIT |
| 2. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT | |
| Rough idling (Poor idling) | 1. Compression | ON-VEHICLE INSPECTION |
| 2. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT | |
| Hunting (Poor idling) | 1. ECM power source circuit | ECM POWER SOURCE CIRCUIT |
| 2. A/T faulty | AUTOMATIC TRANSMISSION SYSTEM | |
| Hesitation/Poor acceleration (Poor driveability) | 1. Fuel pump control circuit | FUEL PUMP CONTROL CIRCUIT |
| 2. A/T faulty | AUTOMATIC TRANSMISSION SYSTEM | |
| Engine stalls during A/C operatio | 1. A/C signal circuit (Comoressor circuit) | COMPRESSOR CIRCUIT |
| 2. ECM | ECM | |
| Unable/Difficult to refuel | 1. ORVR system | - |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.