Inspection Procedure

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG) and push the tester main switch ON.
3. Check the ECUs connected to CAN bus (see DIAGNOSIS SYSTEM ).

   Result 

   RESULT CHART
   
   

   Result	Proceed to
   No malfunction appears	A
   Malfunction appears	B

B: GO TO CAN COMMUNICATION SYSTEM  (See CAN COMMUNICATION SYSTEM )

A: GO TO NEXT STEP 

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG) and push the tester main switch ON.
3. Check for DTCs.

   Result 

   RESULT CHART
   
   

   Condition	Proceed to
   DTC is not output	A
   CAN system DTC is output	B
   LIN system DTC is output	C

B: GO TO CAN COMMUNICATION SYSTEM  (See CAN COMMUNICATION SYSTEM )

C: GO TO LIN COMMUNICATION SYSTEM  (See HOW TO PROCEED WITH TROUBLESHOOTING )

A: GO TO NEXT STEP 

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG) and push the tester main switch ON.
3. Enter the following menus:
   1. Intelligent tester - Select: DIAGNOSIS / OBD/MOBD / BODY / METER / ACTIVE TEST.
   2. Techstream - Select: Body / Combination Meter / Active Test.
4. Check the condition of the pattern select indicator light by operating the tester.
   1. Intelligent tester

      METER 

      METER TESTER DISPLAY REFERENCE
      
      

      Tester Display	Test Part	Control Range	Diagnostic Note
      ECT PWR INDIC	Pattern select indicator light (PWR)/	ON or OFF	-
      ECT SNOW INDIC	Pattern select indicator light (SNOW)/	ON or OFF	-

   2. Techstream

      Combination Meter 

      COMBINATION METER TESTER DISPLAY REFERENCE
      
      

      Tester Display	Test Part	Control Range	Diagnostic Note
      Indicat. Lamp ECT PWR	Pattern select indicator light (PWR)/	ON or OFF	-
      Indicat. Lamp ECT SNOW	Pattern select indicator light (SNOW)/	ON or OFF	-

      OK: Indicator light turns on or off according to the tester operation. 

NG: GO TO METER / GAUGE SYSTEM  (See HOW TO PROCEED WITH TROUBLESHOOTING )

OK: GO TO NEXT STEP 

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG) and push the tester main switch ON.
3. Enter the following menus:
   1. Intelligent tester - Select: DIAGNOSIS / OBD/MOBD / BODY / CENTER CONSOLE / DATA LIST.
   2. Techstream - Select: Body / Center Console Switch / Data List.
4. Read the value displayed on the tester.
   1. Intelligent tester

      CENTER CONSOLE 

      CENTER CONSOLE TESTER DISPLAY REFERENCE
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      ECT PWR SW	Pattern select switch (PWR) status/ ON or OFF	Pattern select switch (PWR) is: ON: Pushed OFF: Not pushed	-
      ECT SNOW SW	Pattern select switch (SNOW) status/ ON or OFF	When turning engine switch on (IG): OFF ↓ Pattern select switch (ECT SNOW) is: Pushed: ON ↓ Pattern select switch (ECT SNOW) is: Pushed again: OFF	-

   2. Techstream

      Center Console Switch 

      CENTER CONSOLE SWITCH TESTER DISPLAY REFERENCE
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      ECT Power Mode Switch	Pattern select switch (PWR) status/ ON or OFF	Pattern select switch (PWR) is: ON: Pushed OFF: Not pushed	-
      ECT Snow Mode Switch	Pattern select switch (SNOW) status/ ON or OFF	When turning engine switch on (IG): OFF ↓ Pattern select switch (ECT SNOW) is: Pushed: ON ↓ Pattern select switch (ECT SNOW) is: Pushed again: OFF	-

      OK: On tester screen, item changes between ON and OFF according to switch operation. 

NG: REPLACE NO. 1 CONSOLE SWITCH 

OK: GO TO NEXT STEP 

1. Replace the TCM (see REMOVAL  ).

NEXT: PERFORM AT REGISTRATION (See  REGISTRATION   )