2007 Lexus LS 460LFACTORY OEM SERVICE PROCEDURE

Height Control Compressor: Installation

  1. INSTALL HEIGHT CONTROL COMPRESSOR 
      Fig 1: Locating Bushings And Bracket
      G04944188Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Install the 3 bushings and bracket to the height control compressor with the 3 bolts.

      Torque: 5.9 N*m (60 kgf*cm, 52 in.*lbf) 

    2. Push the connector into the housing until a clicking sound is heard.
    3. Attach the 3 clamps.
    4. Install the height control sensor with the bolt and 2 nuts.

      Torque: 19.1 N*m (195 kgf*cm, 14 ft.*lbf) 

      Fig 2: Locating Height Control Sensor And Nuts
      G04944187Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Connect the height control tube (see SUSPENSION CONTROL SYSTEM  ).
    6. Connect the height control filter to the bumper reinforcement.
    7. Connect the 2 connectors and attach the 2 clamps.
      Fig 3: Locating Connectors And Clamps
      G04944186Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  3. INSTALL COWL TOP VENTILATOR LOUVER RH  (See INSTALLATION )
  4. PERFORM INITIALIZATION 
    1. Perform initialization (see INITIALIZATION ).
      NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
  5. CHECK SRS WARNING LIGHT 
    1. Check the SRS warning light (see DIAGNOSIS SYSTEM ).
  6. INSPECT FOR AIR LEAK 
    1. Inspect for air leak (see OPERATION CHECK  ).
  7. INSTALL FRONT FENDER LINER RH 
    1. Install the 2 bolts.
  8. INSTALL FRONT BUMPER COVER  (See INSTALLATION )
  9. INSTALL FRONT FENDER LINER LH  (See INSTALLATION )
  10. INSTALL FRONT FENDER LINER RH  (See INSTALLATION )
  11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH  (See INSTALLATION )
  12. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH  (See INSTALLATION )
  13. INSTALL FRONT FENDER WHEEL OPENING MOULDING LH  (See INSTALLATION )
  14. INSTALL FRONT FENDER WHEEL OPENING MOULDING RH  (See INSTALLATION )
  15. INSTALL RADIATOR GRILLE ASSEMBLY  (See INSTALLATION )
  16. INSTALL COOL AIR INTAKE DUCT SEAL  (See INSTALLATION )
  17. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY  (See INSTALLATION )
  18. INSTALL ENGINE ROOM SIDE COVER LH  (See INSTALLATION )
  19. REMOVE ENGINE ROOM SIDE COVER RH  (See INSTALLATION )
  20. INSTALL FRONT WHEEL RH 

    Torque: 140 N*m (1428 kgf*cm, 103 ft.*lbf) 

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.