2007 Lexus LS 460LFACTORY OEM SERVICE PROCEDURE

Power Window Control System: Initialization

  1. INITIALIZE POWER WINDOW CONTROL SYSTEM (POWER WINDOW REGULATOR MOTOR (ALL DOORS)) 
    CAUTION: When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized. Functions such as the AUTO UP/DOWN, jam protection and key-off do not operate if the initialization is not performed.

    HINT:

    When the battery is replaced, it is not necessary to initialize the power window regulator motor.

    NOTE:
    • When the power window regulator motor assembly is replaced, DTC B2313 is output. Clear the DTC after the initialization.
    • When performing initialization, do not perform any other procedures.
    • After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used, due to detection of the different operation learned value of the door glass movement speed. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
      1. Open the power window by fully pushing down the switch.
      2. Close the power window by fully pulling up the power window switch and holding it at the AUTO UP position.
    • If the initialization is not completed properly, the LIN communication system may have a malfunction (see HOW TO PROCEED WITH TROUBLESHOOTING ).
    1. Initialization procedures when replacing the power window regulator motor with new one
      1. Connect the battery and turn the engine switch on (IG). (At this time, the LED on the power window regulator switch blinks to indicate that it is ready for initialization.)
      2. Fully open the window by fully pushing the power window regulator switch, and hold the switch for 1 second or more after the window is fully opened.
      3. Fully close the power window by fully pulling the power window regulator switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position. The LED on the power window regulator switch changes from blinking to illuminated to indicate that the initialization is complete.
    2. Initialization procedures when removing/installing the power window regulator motor assembly
      1. Connect the battery and turn the engine switch on (IG). (At this time, the LED on the power window regulator switch blinks to indicate that it is ready for initialization.)
      2. Fully close the power window by fully pulling the power window regulator switch, and hold the switch for 6 seconds or more after the window is fully closed. (If the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again.)
      3. Fully open the window by pushing down the power window regulator switch, and hold the switch for 1 second or more after the window is fully opened.
      4. Release the power window regulator switch. Then fully push and hold the switch 4 seconds or more.
      5. Fully close the power window by fully pulling the power window regulator switch, and hold the switch 1 second or more after the window is fully closed to reset the glass position. The LED on the power window regulator switch changes from blinking to illuminated to indicate that the initialization is complete.
    3. Initialization procedures when the power window does not fully open
      1. Perform the initialization procedures when removing/installing the power window regulator motor assembly.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.