Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Lexus IS 350FACTORY OEM SERVICE PROCEDURE
Torque Specifications
WARNING: This page is about a different car, the 2007 Lexus IS 250. However, it is still accessible from the selected car via links, so may be relevant.
AIR CONDITIONING TORQUE SPECIFICATIONS
| Part Tightened | N*m | kgf*cm | ft.*lbf |
|---|---|---|---|
| AIR CONDITIONING UNIT | |||
| Air conditioning radiator assembly x Blower assembly | 3.0 | 31 | 27 in.*lbf |
| Air conditioning unit assembly x Body | 9.8 | 100 | 7 |
| Instrument panel reinforcement assembly x Body (Collar) | 6.0 | 61 | 53 in.*lbf |
| Instrument panel reinforcement assembly x Body ("Torx" bolt) | 20 | 204 | 15 |
| Air conditioning tube assembly x Cooler expansion valve | 3.5 | 35 | 30 in.*lbf |
| Suction pipe sub-assembly x Air conditioning tube assembly | 9.8 | 100 | 7 |
| BLOWER UNIT | |||
| Air conditioning radiator assembly x Blower assembly | 3.0 | 31 | 27 in.*lbf |
| Blower assembly x Instrument panel reinforcement assembly (Bolt:) | 9.8 | 100 | 7 |
| No. 2 Air duct x Blower assembly | 5.4 | 55 | 48 in.*lbf |
| COMPRESSOR AND MAGNETIC CLUTCH | |||
| Compressor and magnetic clutch x Engine | 25 | 255 | 18 |
| Discharge hose sub-assembly x Compressor and magnetic clutch | 9.8 | 100 | 7 |
| No. 1 cooler refrigerant suction hose x Compressor and magnetic clutch | 9.8 | 100 | 7 |
| Magnet clutch hub x Cooler compressor assembly | 18 | 184 | 13 |
| Oil filter bracket sub-assembly | 21 | 214 | 15 |
| Compressor and magnetic clutch (stud bolt) x Engine | 10 | 102 | 7 |
| CONDENSER | |||
| Cooler condenser assembly x Radiator assembly | 5.0 | 51 | 44 in.*lbf |
| Discharge hose sub-assembly x Cooler condenser assembly | 5.4 | 55 | 47 in.*lbf |
| Liquid tube sub-assembly x Cooler condenser assembly | 5.4 | 55 | 47 in.*lbf |
| Cap x cooler condenser assembly | 2.9 | 30 | 26 in.*lbf |
| SMOG VENTILATION SENSOR | |||
| Smog ventilation sensor | 9.8 | 100 | 7 |
| HEATER GLOW PLUG | |||
| Water by-pass glow plug x Water hose joint | 15 | 157 | 11 |
| Heater blower wire x Water bypass glow plug | 2.7 | 28 | 24 in.*lbf |
| WATER HOSE JOINT | |||
| Water hose joint x Intake air surge tank | 10 | 102 | 7 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.