Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Lexus IS 350FACTORY OEM SERVICE PROCEDURE
Body Electrical: Clock: Removal
NOTE:
When disassembling the clock assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
- REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission) (See Step 4 in REMOVAL )
- REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) (See Step 5 in REMOVAL )
- REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH (for Automatic Transmission) (See Step 6 in REMOVAL )
- REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH (for Automatic Transmission) (See Step 7 in REMOVAL )
- REMOVE CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transmission) (See Step 8 in REMOVAL )
- REMOVE REAR CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission) (See Step 9 in REMOVAL )
- REMOVE FRONT CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission) (See Step 10 in REMOVAL )
- REMOVE FRONT ASH RECEPTACLE SUB-ASSEMBLY (See Step 11 in REMOVAL )
- REMOVE CONSOLE BOX REGISTER ASSEMBLY (See Step 12 in REMOVAL )
- REMOVE CONSOLE BOX (See Step 13 in REMOVAL )
- REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY (See Step 14 in REMOVAL )
- REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL (See Step 15 in REMOVAL )
- REMOVE INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System) (See Step 13 in REMOVAL )
- REMOVE NO. 1 RADIO BRACKET (w/o Navigation System) (See Step 14 in REMOVAL )
- REMOVE NO. 2 RADIO BRACKET (w/o Navigation System) (See Step 15 in REMOVAL )
- REMOVE RADIO RECEIVER ASSEMBLY (w/o Navigation System) (See Step 16 in REMOVAL )
- REMOVE CLOCK ASSEMBLY (w/o Navigation System)
- Remove the 6 screws.
- Disengage the 5 claws and integration control panel.
- Remove the 9 screws and cover.
- Disconnect the connectors.
- Remove the clock assembly.
- REMOVE MULTI-DISPLAY ASSEMBLY (w/ Navigation System) (See Step 17 in REMOVAL )
- REMOVE NO. 1 RADIO BRACKET (w/ Navigation System) (See Step 18 in REMOVAL )
- REMOVE NO. 2 RADIO BRACKET (w/ Navigation System) (See Step 19 in REMOVAL )
- REMOVE RADIO RECEIVER ASSEMBLY (w/ Navigation System) (See Step 20 in REMOVAL )
- REMOVE CLOCK ASSEMBLY (w/ Navigation System)
- Apply protective tape to the places shown.
- Insert 2 precision screwdrivers (
1.5 or less) into the holes on both sides of the clock assembly at the angle as shown in Fig 6
.NOTE: Do not pry on the clock assembly with the screwdrivers as it may damage the clock assembly.
HINT:
If precision screwdrivers are not available, use in-vehicle tools (part No. 09135-53010).
- Insert a screwdriver with its tip taped from the underside of the hazard switch, and pull and remove the clock assembly.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
