2007 Lexus IS 350FACTORY OEM SERVICE PROCEDURE

Power Window Regulator Motor: Inspection

  1. INSPECT POWER WINDOW REGULATOR MOTOR (FRONT RH) 
    1. Apply battery voltage to the motor connector according to POWER WINDOW REGULATOR MOTOR (FRONT RH)  .
      NOTE: Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard 

    POWER WINDOW REGULATOR MOTOR (FRONT RH)

    Measurement Condition Specified Condition
    Battery positive (+) --> Terminal 1 (D)
    Battery negative (-) --> Terminal 2 (U)
    Motor gear rotates clockwise
    Battery positive (+) --> Terminal 2 (U)
    Battery negative (-) --> Terminal 1 (D)
    Motor gear rotates counterclockwise
    Fig 1: Identifying Power Window Regulator Motor Connector Terminals
    G04050725Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT POWER WINDOW REGULATOR MOTOR (FRONT LH) 
    1. Apply battery voltage to the motor connector according to MEASUREMENT CONDITION AND SPECIFIED CONDITION TABLE  .
      NOTE: Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard 

    MEASUREMENT CONDITION AND SPECIFIED CONDITION TABLE

    Measurement Condition Specified Condition
    Battery positive (+) --> Terminal 2 (U)
    Battery negative (-) --> Terminal 1 (D)
    Motor gear rotates clockwise
    Battery positive (+) --> Terminal 1 (D)
    Battery negative (-) --> Terminal 2 (U)
    Motor gear rotates counterclockwise
    Fig 2: Identifying Power Window Regulator Motor Connector Terminals
    G04050731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSPECT POWER WINDOW REGULATOR MOTOR (REAR RH) 
    1. Apply battery voltage to the motor connector according to POWER WINDOW REGULATOR MOTOR (REAR RH)  .
      NOTE: Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard 

    POWER WINDOW REGULATOR MOTOR (REAR RH)

    Measurement Condition Specified Condition
    Battery positive (+) --> Terminal 2 (U)
    Battery negative (-) --> Terminal 1 (D)
    Motor gear rotates clockwise
    Battery positive (+) --> Terminal 1 (D)
    Battery negative (-) --> Terminal 2 (U)
    Motor gear rotates counterclockwise
    Fig 3: Identifying Power Window Regulator Motor Connector Terminals
    G04050731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSPECT POWER WINDOW REGULATOR MOTOR (REAR LH) 
    1. Apply battery voltage to the motor connector according to POWER WINDOW REGULATOR MOTOR (REAR LH)  .
      NOTE: Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard 

    POWER WINDOW REGULATOR MOTOR (REAR LH)

    Measurement Condition Specified Condition
    Battery positive (+) --> Terminal 1 (D)
    Battery negative (-) --> Terminal 2 (U)
    Motor gear rotates clockwise
    Battery positive (+) --> Terminal 2 (U)
    Battery negative (-) --> Terminal 1 (D)
    Motor gear rotates counterclockwise
    Fig 4: Identifying Power Window Regulator Motor Connector Terminals
    G04050725Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.