2007 Lexus GX 470FACTORY OEM SERVICE PROCEDURE

Windshield Glass: Installation

  1. INSTALL WINDSHIELD GLASS STOPPER NO. 2 
    1. Coat the installation part of the stopper with Primer G.
      NOTE:
      • Allow the primer coating to dry for 3 minutes or more.
      • Do not keep any of the opened Primer G for later use.
      • Do not apply too much primer.
    2. Install 2 new windshield glass stoppers onto the glass.

      Standard dimension 

    DIMENSION SPECIFICATION

    Area Dimension
    A 40.0 mm (1.575 in.)
    B 7.8 mm (0.307 in.)
    Fig 1: Identifying Windshield Glass Stoppers Dimension
    G05266789Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER 
    Fig 2: Identifying Windshield Glass Stopper
    G05266790Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Install 2 new No. 1 stoppers to the vehicle body.

      HINT:

      Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.

  3. INSTALL WINDSHIELD MOLDING 
    1. Using a brush or sponge, coat the application area of molding with Primer G.
    NOTE:
    • Do not apply too much primer.
    • Allow the primer coating to dry for 3 minutes or more.
    • Do not keep any of the opened Primer G for later use.
  4. INSTALL WINDOW GLASS ADHESIVE DAM 
    1. Using a brush or sponge, coat the application area of adhesive dam with Primer G.
      NOTE:
      • Do not apply too much primer.
      • Allow the primer coating to dry for 3 minutes or more.
      • Do not keep any of the opened Primer G for later use.

      HINT:

      If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

    2. Fig 3: Identifying Window Glass Adhesive Dam Dimensions
      G05266791Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install a new adhesive dam onto the windshield glass.
      NOTE: Install the new adhesive dam along the ceramic notches.

      Standard dimension 

    DIMENSION SPECIFICATION

    Area Dimension
    C 9.5 mm (0.374 in.)
    D 31.4 mm (1.236 in.)
  5. INSTALL WINDSHIELD GLASS ASSEMBLY 
    1. Position the windshield glass assembly.
      1. Using a suction cup, place the windshield glass assembly in the correct position.
      2. Check that the whole contact surface of the windshield glass rim is perfectly even.
      3. Fig 4: Identifying Matchmarks On Windshield Glass & Vehicle Body
        G04981116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Align the matchmarks on the windshield glass and vehicle body.
        NOTE: Check that the windshield glass stoppers are attached to the vehicle body correctly.
      5. Remove the windshield glass assembly.
    2. Fig 5: Coating Installation Surface On Vehicle Body With Primer M
      G04833927Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a brush, coat the installation surface on the vehicle body with Primer M.
      NOTE:
      • Do not coat the adhesive with Primer M.
      • Do not apply too much primer.
      • Allow the primer coating to dry for 3 minutes or more.
      • Do not keep any of the opened Primer M for later use.

      HINT:

      If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

    4. Using a brush or sponge, coat the application area of adhesive with Primer G.
      NOTE:
      • Do not apply too much primer.
      • Allow the primer coating to dry for 3 minutes or more.
      • Do not keep any of the opened Primer G for later use.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.