2007 Lexus GS 450hFACTORY OEM SERVICE PROCEDURE

Charging Systems: Charging: Battery: Installation

  1. INSTALL BATTERY TRAY (for Active Stabilizer System) 
    1. Install the tray with the 3 bolts.

      Torque: 4.9 N*m (50 kgf*cm, 43 in.*lbf) 

  2. INSTALL ACTIVE STABILIZER BATTERY CURRENT SENSOR ASSEMBLY (for Active Stabilizer System) 
    1. Install the cable to the body panel with the bolt.

      Torque: 8.4 N*m (86 kgf*cm, 74 in.*lbf) 

    2. Install the sensor with the bolt.

      Torque: 13 N*m (133 kgf*cm, 10 ft.*lbf) 

    3. Connect the sensor connector.
      Fig 1: Locating Sensor Connector
      G05303668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL NO. 2 BATTERY (for Active Stabilizer System) 
    1. Install the battery.
    2. Install the battery clamp with the bolt and nut.

      Torque: 4.9 N*m (50 kgf*cm, 43 in.*lbf) for bolt 

      2.9 N*m (30 kgf*cm, 26 in.*lbf) for nut 

    3. Connect the battery room ventilation hose.
    4. Install the battery insulator.
    5. Connect the cable to the positive (+) battery terminal.

      Torque: 5.6 N*m (57 kgf*cm, 50 in.*lbf) 

    6. Connect the cable to the negative (-) battery terminal.

      Torque: 5.6 N*m (57 kgf*cm, 50 in.*lbf) 

    7. Fig 2: Locating Battery Terminal
      G05303667Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL BATTERY TRAY 
    1. Install the tray with the 3 bolts.

      Torque: 4.9 N*m (50 kgf*cm, 43 in.*lbf) 

  5. INSTALL BATTERY 
    1. Install the battery.
    2. Install the battery clamp with the bolt and nut.

      Torque: 4.9 N*m (50 kgf*cm, 43 in.*lbf) for bolt 

      2.9 N*m (30 kgf*cm, 26 in.*lbf) for nut 

      Fig 3: Locating Battery Clamp
      G05303666Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the wire harness of the fuse holder's clamp to the battery clamp.
    4. Connect the thermistor sensor connector.
    5. Connect the battery room ventilation hose.
    6. Connect the cable to the positive (+) battery terminal.

      Torque: 5.6 N*m (57 kgf*cm, 50 in.*lbf) 

    7. Connect the cable to the negative (-) battery terminal.

      Torque: 5.6 N*m (57 kgf*cm, 50 in.*lbf) 

      NOTE: When the warning light is illuminated or the battery has been disconnected and reconnected, turning the power switch may not start the system on the first try. If so, turn the power switch again.
  6. INSTALL TOOL BOX  (See INSTALLATION )
  7. INSTALL BATTERY SERVICE HOLE COVER LH  (See INSTALLATION )
  8. INSTALL LUGGAGE COMPARTMENT FLOOR MAT  (See INSTALLATION )
  9. INSTALL SERVICE PLUG GRIP  (See INSTALLATION )
  10. PERFORM INITIALIZATION 
    1. Perform initialization (see INITIALIZATION (2006/02-2006/07) ).
      NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal
Chapter Navigation
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.