2007 Lexus GS 430FACTORY OEM SERVICE PROCEDURE

Inspection Procedure

  1. CHECK FUEL PUMP OPERATION 
    1. Check if there is pressure in the fuel inlet hose.

      HINT:

      If there is fuel pressure, you will hear the sound of fuel flowing.

    OK:  Go to step  12

    NG: Go to next step 

  2. PERFORM ACTIVE TEST (OPERATE C/OPN RELAY) 
    1. Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.
    2. Turn the engine switch on (IG) and turn the tester ON.
    3. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD.
    4. Check the relay operation while operating it using the tester.

      OK: 

      Operating noise can be heard from the relay. 

    OK:  Go to step  8

    NG: Go to next step 

  3. INSPECT ECM POWER SOURCE CIRCUIT 

    NG: REPAIR ECM POWER SOURCE CIRCUIT 

    OK: Go to next step 

  4. INSPECT FUSE (F/PUMP) 
    1. Remove the F/PMP fuse from the engine room No. 2 junction block.
    2. Measure the resistance of the fuse.

      Standard resistance: 

      Below 1 Ω 

    Fig 1: Identifying F/PMP Fuse
    G05285725Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE 

    OK: Go to next step 

  5. INSPECT INTEGRATION RELAY (Marking EFI NO. 2) 
    1. Remove the integration relay from the engine room No. 2 junction block.
    2. Measure the resistance of the EFI NO. 2 relay.

      Standard resistance 

      TERMINAL CONNECTIONS SPECIFIED CONDITION CHART

      Terminal Connections Specified Condition
      2B-7 - 2C-1 10 kΩ or higher
      2B-7 - 2C-1 Below 1 Ω
      (when battery voltage is applied to terminals 2A-8 and 2B-3)
    Fig 2: Identifying Integration Relay
    G05285472Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPLACE INTEGRATION RELAY 

    OK: Go to next step 

  6. CHECK WIRE HARNESS (ECM - C/OPN RELAY) 
    1. Remove the integration relay from the engine room No. 2 junction block.
    2. Disconnect the A6 ECM connector.
    3. Measure the resistance of the wire harness side connectors.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      2B-7 - A6-14 (FC) Below 1 Ω
      2B-7 or A6-14 (FC) - Body ground 10 kΩ or higher
    Fig 3: Checking Wire Harness (ECM - C/OPN Relay)
    G05285727Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPAIR OR REPLACE HARNESS AND CONNECTOR 

    OK: Go to next step 

  7. CHECK ECM (FC VOLTAGE) 
    1. Turn the engine switch on (IG).
    2. Measure the voltage of the ECM connector.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      A6-14 (FC) - E7-7 (E1) 9 to 14 V
    Fig 4: Checking ECM (FC Voltage)
    G05285728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPLACE ECM 

    NG: REPLACE INTEGRATION RELAY 

  8. INSPECT RELAY (Marking: F/PMP) 
    1. Remove the F/PMP relay from the engine room No. 2 relay block.
    2. Measure the resistance of the relay.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      3 - 4 Below 1 Ω
      3 - 4 10 kΩ or more
      (when battery voltage is applied to terminals 1 and 2)
    Fig 5: Identifying F/PMP Relay
    G05285729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPLACE RELAY 

    OK: Go to next step 

  9. INSPECT FUEL PUMP 
    1. Check the resistance of the fuel pump.
      1. Measure the resistance between terminals 4 and 5.

        Standard resistance: 

        0.2 to 3.0 Ω at 20°C (68°F) 

    2. Check operation of the fuel pump.
      1. Apply battery voltage to both terminals. Check that the pump operates.
        NOTE:
        • These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
        • Keep fuel pump as far away from the battery as possible.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.