Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
VC Output Circuit: Wiring Diagram
Refer to WIRING DIAGRAMÂ .
- CHECK MILÂ
- Check that Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).
OK: MIL lights up.Â
OK : ENDÂ
NG : GO TO NEXT STEPÂ
- Check that Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).
- CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECMÂ
- Connect the intelligent tester to the DLC3.
- Turn the engine switch to ON and tester on.
- Check the communication between the tester and ECM.
ResultÂ
RESULT REFERENCEResult Proceed to Communication is possible A Communication is not possible B
A : GO TO Â MIL CIRCUITÂ Â
B : GO TO NEXT STEPÂ
- CHECK THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)Â
- Disconnect the throttle body connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the throttle body connector.
A : REPLACE THROTTLE BODY ASSEMBLYÂ
B : GO TO NEXT STEPÂ
- CHECK ACCELERATOR PEDAL ASSEMBLY (CHECK MIL ILLUMINATED)Â
- Disconnect the accelerator pedal position sensor connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the accelerator pedal position sensor connector.
A : REPLACE ACCELERATOR PEDAL ASSEMBLYÂ
B : GO TO NEXT STEPÂ
- CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)Â
- Disconnect the VVT sensor for intake camshaft bank 1 connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the VVT sensor for intake camshaft bank 1 connector.
A : REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 1Â
B : GO TO NEXT STEPÂ
- CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)Â
- Disconnect the VVT sensor for exhaust camshaft bank 1 connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the VVT sensor for exhaust camshaft bank 1 connector.
A : REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1Â
B : GO TO NEXT STEPÂ
- CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)Â
- Disconnect the VVT sensor for intake camshaft bank 2 connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the VVT sensor for intake camshaft bank 2 connector.
A : REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 2Â
B : GO TO NEXT STEPÂ
- CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)Â
- Disconnect the VVT sensor for exhaust camshaft bank 2 connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the VVT sensor for exhaust camshaft bank 2 connector.
A : REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2Â
B : GO TO NEXT STEPÂ
- CHECK FUEL PRESSURE SENSOR (CHECK MIL ILLUMINATED)Â
- Disconnect the fuel pressure sensor connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the fuel pressure sensor connector.
A : REPLACE FUEL PRESSURE SENSORÂ
B : GO TO NEXT STEPÂ
- CHECK CHARCOAL CANISTER ASSEMBLY (CHECK MIL ILLUMINATED)Â
- Disconnect the canister pump module connector.
- Turn the engine switch on (IG).
- Check the MIL.
ResultÂ
RESULT REFERENCEResult Proceed to MIL illuminates A MIL does not illuminate B - Reconnect the canister pump module connector.
A : REPLACE CHARCOAL CANISTER ASSEMBLYÂ
B : GO TO NEXT STEPÂ
- CHECK HARNESS AND CONNECTORÂ
- Disconnect the throttle body connector.
- Disconnect the accelerator pedal position sensor connector.
- Disconnect the VVT sensor for intake camshaft bank 1 connector.
- Disconnect the VVT sensor for exhaust camshaft bank 1 connector.
- Disconnect the VVT sensor for intake camshaft bank 2 connector.
- Disconnect the VVT sensor for exhaust camshaft bank 2 connector.
- Disconnect the fuel pressure sensor connector.
- Disconnect the canister pump module connector.
- Disconnect the D3, D5 and A5 ECM connectors.
- Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for short)Â
RESISTANCE SPECIFICATIONTester Connections Specified Conditions VCTA (E3-27) - Body ground 10 kΩ or higher VCV1 (E3-23) - Body ground 10 kΩ or higher VCV2 (E3-20) - Body ground 10 kΩ or higher VCPR (E6-31) - Body ground 10 kΩ or higher VCE1 (E6-22) - Body ground 10 kΩ or higher VCE2 (E6-19) - Body ground 10 kΩ or higher VCPA (A6-35) - Body ground 10 kΩ or higher VCP2 (A6-27) - Body ground 10 kΩ or higher VCPP (A5-22) - Body ground 10 kΩ or higher - Reconnect the ECM connectors.
- Reconnect the canister pump module connector.
- Reconnect the fuel pressure sensor connector.
- Reconnect the VVT sensor for exhaust camshaft bank 2 connector.
- Reconnect the VVT sensor for intake camshaft bank 2 connector.
- Reconnect the VVT sensor for exhaust camshaft bank 1 connector.
- Reconnect the VVT sensor for intake camshaft bank 1 connector.
- Reconnect the accelerator pedal position sensor connector.
- Reconnect the throttle body connector.
NG : REPAIR OR REPLACE HARNESS OR CONNECTORÂ
OK : REPLACE ECMÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
