2006 Lexus GS 430FACTORY OEM SERVICE PROCEDURE

Automatic Transmission Unit: Disassembly

  1. REMOVE TRANSAXLE CASE COVER UPPER 
    1. Remove the 2 bolts and transaxle case cover upper.
  2. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH 
    1. Remove the nut, spring washer and the transmission control shaft lever RH.
      Fig 1: Identifying Transmission Control Shaft Lever RH
      G04028520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Using a screwdriver, unstake the lock washer.
    2. Remove the nut and lock washer.
    3. Remove the bolt and park/neutral position switch.
      Fig 2: Identifying Bolt And Park/Neutral Position Switch
      G04028521Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE OIL COOLER TUBE UNION 
    1. Remove the 2 oil cooler tube unions.
    2. Remove the O-rings from the oil cooler tube unions.
      Fig 3: Identifying Oil Cooler Tube Unions
      G04028522Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE TRANSMISSION REVOLUTION SENSOR 
    1. Remove the 2 bolts and the 2 transmission revolution sensors.
    2. Remove the O-rings from each sensor.
      Fig 4: Identifying Transmission Revolution Sensors
      G04028523Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE 
    1. Remove the 2 bolts.
    2. Remove the breather tube.
      Fig 5: Identifying Automatic Transmission Breather Tube
      G04028524Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE AUTOMATIC TRANSMISSION HOUSING 
    1. Remove the 10 bolts.
    2. Remove the transmission housing.
      Fig 6: Identifying Automatic Transmission Housing
      G04028525Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE AUTOMATIC TRANSMISSION FLANGE YOKE ASSEMBLY 
    1. Using a hammer and chisel, loosen the staked part of the nut.
    2. Remove the nut and flange yoke.
      Fig 7: Loosening Staked Part Of Nut
      G04028526Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the oil seal from the flange yoke.
      Fig 8: Identifying Oil Seal From Flange Yoke
      G04028527Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE EXTENSION (ATM) HOUSING SUBASSEMBLY 
    1. Remove the 6 bolts.
      Fig 9: Identifying Bolts
      G04028528Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Use a screwdriver to remove the extension housing sub-assembly.
      Fig 10: Identifying Extension Housing Sub-Assembly
      G04028529Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a snap ring expander, remove the snap ring.
    4. Remove the thrust needle roller bearing and the 2 bearing races.
      Fig 11: Identifying Snap Ring
      G04028530Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE RR COVER SLEEVE 
    1. Remove the 2 washers and RR cover sleeve.
  11. REMOVE TRANSMISSION CASE ADAPTOR RADIAL BALL BEARING 
    1. Remove the transmission case adaptor radial ball bearing from the extension housing sub-assembly.
      Fig 12: Identifying Washers And RR Cover Sleeve
      G04028531Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL 
    1. Using a screwdriver, remove the oil seal.
      Fig 13: Identifying Automatic Transmission Extension Housing Oil Seal
      G04028532Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. FIX AUTOMATIC TRANSMISSION CASE SUBASSEMBLY 
    1. Install the transmission case on the overhaul attachment.
      Fig 14: Identifying Transmission Case On Overhaul Attachment
      G04028533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY 
    NOTE: Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the pan.
    1. Remove the over flow plug and the gasket.
    2. Remove the drain plug and the gasket.
    3. Remove the 20 bolts, oil pan and gasket.
    4. Examine particles in the pan.
      1. Remove the magnets from the oil pan. Use the removed magnets to collect any steel chips. Look carefully at the chips and particles in the pan and on the magnet to anticipate what type of wear you will find in the transaxle.

        Steel (magnetic): bearing, gear and plate wear Brass (non-magnetic): bearing wear

        Fig 15: Inspecting For Chips And Steel Particles In Pan
        G04089157Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE VALVE BODY OIL STRAINER ASSEMBLY 
    1. Turn over the transmission.
    2. Remove the 4 bolts and valve body oil strainer assembly from the valve body.
    3. Remove the O-ring from the valve body oil strainer assembly.
      Fig 16: Identifying Valve Body Oil Strainer Assembly From Valve Body
      G04028535Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE TRANSMISSION WIRE 
    1. Remove the 3 bolts and disconnect the 3 clamps.
    2. Disconnect the 9 connectors from the shift solenoid valves.
      Fig 17: Identifying Connectors From Shift Solenoid Valves
      G04028536Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the bolt from the transmission case.
    4. Pull the transmission wire out of the transmission case.
    5. Remove the O-ring from the transmission wire.
      Fig 18: Locating Transmission Internal Wiring Harness bolt
      G04019558Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE TRANSMISSION VALVE BODY ASSEMBLY 
    1. Remove the bolt, the detent spring cover and detent spring.
      Fig 19: Identifying Detent Spring Cover And Detent Spring
      G04028538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 20 bolts.
    3. Remove the valve body assembly.
      Fig 20: Identifying Valve Body Assembly
      G04028539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE TRANSAXLE CASE GASKET 
    1. Remove the 3 transaxle case gaskets.
      Fig 21: Identifying Transaxle Case Gaskets
      G04028540Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE BRAKE DRUM GASKET 
    1. Remove the 3 brake drum gaskets.
      Fig 22: Identifying Brake Drum Gaskets
      G04028541Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE CHECK BALL BODY 
    1. Remove The Check Ball Body And The Spring.
      Fig 23: Identifying Check Ball Body And Spring
      G04028542Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE C-2 ACCUMULATOR PISTON 
    1. While blowing compressed air into the oil hole, remove the C-2 accumulator piston and the spring.
    2. Remove the 2 O-rings from the piston.
      NOTE: Take care as the C-3 and B-3 accumulator piston may jump out.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.