Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Lexus SC 430FACTORY OEM SERVICE PROCEDURE
Technical Service Bulletins
- A/C Compressor
- Accessories & Equipment
- Accessories Control Systems
- Immobilizer And Smart Key Reset (SS002-01)
- TECHSTREAM Ecu Flash Reprogramming Procedure (SS002-07)
- BLUETOOTH® Compatible Cellular Phones (EL014-06)
- Failure To Initialize Can Interface Module (SS001-05)
- Power System Initialization During PDS (PD010-05)
- Navigation System Door Replacement (BO011-04)
- Navigation System Door Opening/Closing Effort (BO010-04)
- Air Bag, SRS
- Anti-Theft Systems
- Automatic Trans
- Interior Electrical Component Precautions (L-SB-0066-11 REV2)
- Automatic Transmission Replacement Precautions (L-SB-0082-14)
- Torque Converter Bolt Installation (L-SB-0007-11 REV1)
- World Standard Automatic Transmission Fluid (TC008-07)
- Alignment Pin Installation During Transmission/Transaxle Assembly Installation (L-SB-0026-08)
- Automatic Transmission Shipping Bag For Warranty Recovery (TC010-07)
- A650E Transmission Solenoid Identification (TC004-05)
- Auxiliary Emission Control Systems
- Battery Management Systems
- Body Electrical
- Body Interior
- Brakes Control Systems
- Charging Systems
- Communication Devices
- Cooling System (Mechanical)
- Cruise Control Systems
- Differentials & Drive Axles
- Driveshaft & Universal Joints
- Engine Control Systems
- Entertainment Systems
- Exhaust
- Exterior Body Panels
- Frames, Subframes & Crossmembers
- Front Suspension
- Gauges & Instrument Panels
- Headlights
- HVAC Control Systems
- Identification
- Replacement Certification Labels And VIN Plates (PG008-07)
- Engine Bank 1 And Bank 2 A/F And O2 Identification (L-SB-0188-09)
- Replacement Certification Labels And VIN Plates - Crib # 164 (S-CRIB-164)
- Engine Serial Number Location (L-SB-0085-08 REV1)
- Replacement VIN Plates (PG007-07)
- Entering VIN During ECM (Pcm) Replacement And/Or DTC P0630 (EG012-04)
- Ignition Switch/Steering Lock
- Infotainment
- Interior/Exterior Trim
- Odor Remediation Process (Dealer Performed) (L-SB-0030-24 REV1)
- Odor Remediation After Water Intrusion (L-SB-0004-22 REV1)
- Interior Electrical Component Precautions (L-SB-0066-11 REV2)
- Trim Removal & Installation - Crib # 167 (L-CRIB-167)
- Navigation System Door Replacement (BO011-04)
- Navigation System Door Opening/Closing Effort (BO010-04)
- Lubrication System
- Mechanical
- Mechanical - Hydraulic
- Mirrors
- Paint & Coatings
- Iron Particle Rust Contamination Repair (L-SB-0020-24)
- New Vehicle Washing Schedule For Paint Protection (L-SB-0024-24)
- Prevention And Repair Of Acid Rain Damage (L-SB-0022-24)
- PAINTLESS Dent Repair - Crib # 146 (T-CRIB-146)
- Plastic Bumper Refinishing - Crib # 170 (L-CRIB-170)
- Permanent-Type Protective Wax Coatings (L-SB-0083-08)
- Acid Rain Paint Finish Damage - Prevention & Repair - Crib # 165 (S-CRIB-165)
- Paint Stains Under RAPGARDâ„¢ (PA001-03 REV.)
- Iron Particle Rust Contamination Repair (PA001-05)
- Parking Brake System
- Passive Restraints
- Procedures
- Rear Suspension
- Restraints Control Systems
- Seats
- Starter
- Steering Column
- Steering Control Systems
- Steering Linkage
- Sun Roof/T-Top/Convertible Top
- Suspension Control Systems
- System
- Transmission Control Systems
- Warning Systems
- Wheel Alignment
- Wheels & Tire System
- Window Motors & Regulators
- Wiper/Washer Systems
- Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
