Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Power Mirror Control System - Diagnostics: Inspection
- INSPECT OUTER MIRROR SWITCH ASSY
- Select L or R on the mirror master switch.
- Measure the resistance of the mirror master switch.
Standard:
MIRROR MASTER SWITCHTester Connection Switch Condition Specified Condition 8 (MSW) - 9 (E) L 100 ohms 8 (MSW) - 9 (E) R Below 1 ohms 8 (MSW) - 9 (E) OFF 10 k ohms or higher If the result is not as specified, replace the switch assy.
- Measure the resistance of the mirror control switch.
Standard:
MIRROR CONTROL SWITCHTester Connection Switch Condition Specified Condition 7 (M+) - 9 (E) UP Approx. 100 ohms 7 (M+) - 9 (E) RIGHT 250 ohms 7 (M+) - 9 (E) DOWN 470 ohms 7 (M+) - 9 (E) LEFT 800 ohms 7 (M+) - 9 (E) OFF 10 k ohms or higher If the result is not as specified, replace the switch assy.
- Measure the resistance of the retract switch.
Standard:
RETRACT SWITCHTester Connection Switch Condition Specified Condition 4 - 5 Retract 10 k ohms or higher 4 - 5 Return Below 1 ohms If the result is not as specified, replace the switch assy.
- Driver side:
INSPECT SEAT MEMORY SWITCH
- INSPECT OUTER REAR VIEW MIRROR ASSY LH
- Apply battery voltage and check the operation of the mirror.
OK:
OUTER REAR VIEW MIRROR ASSY LHMeasurement Condition Specified Condition Battery positive (+) -> Terminal 1
Battery negative (-) -> Terminal 10Turns upward (A) Battery positive (+) -> Terminal 10
Battery negative (-) -> Terminal 1Turns downward (B) Battery positive (+) -> Terminal 9
Battery negative (-) -> Terminal 10Turns left (C) Battery positive (+) -> Terminal 10
Battery negative (-) -> Terminal 9Turns right (D) If the result is not as specified, replace the mirror assy.
- Apply battery voltage and check the operation of the retractable mirror.*
HINT:
*: w/ Retractable mirror
NOTE:- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
OK:
OUTER REAR VIEW MIRROR ASSY LH (W/RETRACTABLE MIRROR)Measurement Condition Mirror Condition Specified Condition Battery positive (+) -> Terminal 3
Battery negative (-) -> Terminal 11Retracted position Moves from retracted position to driving position Battery positive (+) -> Terminal 11
Battery negative (-) -> Terminal 3Driving position Moves from driving position to retracted position If the result is not as specified, replace the mirror assy.
- Inspect the mirror position sensor.
- Apply battery and dry cell battery voltage to the terminals as shown in MIRROR POSITION SENSOR .
- Measure the voltage while the mirror moves between the fully downward and fully upward positions.
Standard:
MIRROR POSITION SENSORMeasurement Connection (Battery) Measurement Connection (Dry Cell Battery) Voltmeter Condition Mirror Condition Specified Condition Battery positive (+) -> Terminal 10 Battery positive (+) -> Terminal 5 Positive (+) lead -- Terminal 6 Turns downward fully 2.8 to 5.0 V Battery negative (-) -> Terminal 1 Battery negative (-) -> Terminal 14 Negative (-) lead -> Terminal 14 Battery positive (+) -> Terminal 1 Battery positive (+) -> Terminal 5 Positive (+) lead -> Terminal 6 Turns upward fully 0 to 1.0 V Battery negative (-) -> Terminal 10 Battery negative (-) -> Terminal 14 Negative (-) lead -> Terminal 14 If the result is not as specified, replace the mirror assy.
- Measure the voltage while the mirror moves between fully turned to the left and fully turned to the right.
Standard:
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
MIRROR MOVES BETWEEN FULLY TURNED TO LEFT & RIGHTMeasurement Connection (Battery) Measurement Connection (Dry cell battery) Voltmeter Condition Mirror Condition Specified Condition Battery positive (+) -> Terminal 9 Battery positive (+) -> Terminal 5 Positive (+) lead -> Terminal 13 Turns to left fully 2.8 to 5.0 V Battery negative (-) -> Terminal 10 Battery negative (-) -> Terminal 14 Negative (-) lead -> Terminal 14 Battery positive (+) -> Terminal 10 Battery positive (+) -> Terminal 5 Positive (+) lead -> Terminal 13 Turns to rightfully 0 to 1.0 V Battery negative (-) -> Terminal 9 Battery negative (-) -> Terminal 14 Negative (-) lead -> Terminal 14 If the result is not as specified, replace the mirror assy.
- Inspect the mirror heater.
- Measure the resistance between terminals 4 and 12 of the connector.
Standard: 3.57 to 4.83 Ω at 25°C (75°F)
- Apply battery voltage and check the operation of mirror heater.
OK:
MIRROR HEATERMeasurement Condition Specified Condition Battery positive (+) -> Terminal 4
Battery negative (-) -> Terminal 12Mirror becomes warn
HINT:
It will take a short time for the mirror to become warm.
If the result is not as specified, replace the mirror assy.
- Measure the resistance between terminals 4 and 12 of the connector.
- Apply battery voltage and check the operation of the mirror.
- INSPECT OUTER REAR VIEW MIRROR ASSY RH
- Apply battery voltage and check the operation of the mirror.
OK:
OPERATION OF MIRRORMeasurement Condition Specified Condition Battery positive (+) -> Terminal 1
Battery negative (-) -> Terminal 10Turns upward (A) Battery positive (+) -> Terminal 10
Battery negative (-) -> Terminal 1Turns downward (B) Battery positive (+) -> Terminal 9
Battery negative (-) -> Terminal 10Turns left (C) Battery positive (+) -> Terminal 10
Battery negative (-) -> Terminal 9Turns right (D) If the result is not as specified, replace the mirror assy.
- Apply battery voltage and check the operation of the retractable mirror.*
HINT:
*: w/ Retractable mirror
NOTE:- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
OK:
OPERATION OF RETRACTABLE MIRRORMeasurement Condition Mirror Condition Specified Condition Battery positive (+) -> Terminal 3
Battery negative (-) -> Terminal 11Retracted position Moves from retracted position to driving position Battery positive (+) -> Terminal 11
Battery negative (-) -> Terminal 3Driving position Moves from driving position to retracted position If the result is not as specified, replace the mirror assy.
- Inspect the mirror position sensor.
- Apply battery and dry cell battery voltage to the terminals as shown in MIRROR POSITION SENSOR .
- Measure the voltage while the mirror moves between the fully downward and fully upward positions.
Standard:
MIRROR POSITION SENSORMeasurement Connection (Battery) Measurement Connection (Dry Cell Battery) Voltmeter Condition Mirror Condition Specified Condition Battery positive (+) -> Terminal 10 Battery positive (+) -> Terminal 5 Positive lead (+) -> Terminal 6 Turns downward fully 2.8 to 5.0 V Battery negative (-) -> Terminal 1 Battery negative (-) -> Terminal 14 Negative lead (-) -> Terminal 14 Battery positive (+) -> Terminal 1 Battery positive (+) -> Terminal 5 Positive lead (+) -> Terminal 6 Turns upward fully 0 to 1.0 V Battery negative (-) -> Terminal 10 Battery negative (-) -> Terminal 14 Negative lead (-) -> Terminal 14 If the result is not as specified, replace the mirror assy.
- Measure the voltage while the mirror moves between fully turned to the left and fully turned to the right.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Standard:
FULLY TURNED TO LEFT AND FULLY TURNED TO RIGHTMeasurement Connection (Battery) Measurement Connection (Dry Cell Battery) Voltmeter Condition Mirror Condition Specified Condition Battery positive (+) -> Terminal 9 Battery positive (+) -> Terminal 5 Positive lead (+) -> Terminal 13 Turns to left fully 0 to 1.0 V Battery negative (-) -> Terminal 10 Battery negative (-) -> Terminal 14 Negative lead (-) -> Terminal 14 Battery positive (+) -> Terminal 10 Battery positive (+) -> Terminal 5 Positive lead (+) -> Terminal 13 Turns to rightfully 2.8 to 5.0 V Battery negative (-) -> Terminal 9 Battery negative (-) -> Terminal 14 Negative lead (-) -> Terminal 14 If the result is not as specified, replace the mirror assy.
- Inspect the operation of the mirror heater.
- Measure the resistance between terminals 4 and 12 of the connector.
Standard: 3.57 to 4.83 Ω at 25°C (75°F)
- Apply battery voltage and check the mirror heater operation.
OK:
MIRROR HEATERMeasurement Condition Specified Condition Battery positive (+) -> Terminal 4
Battery negative (-) -> Terminal 12Mirror becomes warn
HINT:
It will take a short time for the mirror to become warm.
If the result is not as specified, replace the mirror assy.
- Measure the resistance between terminals 4 and 12 of the connector.
- Apply battery voltage and check the operation of the mirror.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
