2005 Lexus RX 330 FWDFACTORY OEM SERVICE PROCEDURE

VVT Sensor: Installation

WARNING: This page is about a different car, the 2007 Lexus RX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL VVT SENSOR (for Bank 2 Exhaust Side) 
    1. Install the VVT sensor with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    2. Connect the VVT sensor connector.
      Fig 1: Locating VVT Sensor Bolt (For Bank 2 Exhaust Side)
      G04973867Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL VVT SENSOR (for Bank 2 Intake Side) 
    1. Install the VVT sensor with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    2. Connect the VVT sensor connector.
      Fig 2: Locating VVT Sensor Bolt (For Bank 2 Intake Side)
      G04973866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL VVT SENSOR (for Bank 1 Exhaust Side) 
    1. Install the VVT sensor with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    2. Connect the VVT sensor connector.
      Fig 3: Locating VVT Sensor Bolt (For Bank 1 Exhaust Side)
      G04973865Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL VVT SENSOR (for Bank 1 Intake Side) 
    1. Install the VVT sensor with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    2. Connect the VVT sensor connector.
  5. INSTALL INTAKE AIR SURGE TANK ASSEMBLY  (See INSTALLATION  )
  6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY  (See INSTALLATION )
  7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY  (See INSTALLATION  )
  8. INSTALL NO. 1 AIR CLEANER INLET  (See INSTALLATION )
  9. INSTALL NO. 2 AIR CLEANER INLET  (See INSTALLATION )
  10. ADD ENGINE COOLANT  (See ON-VEHICLE INSPECTION )
  11. CHECK FOR ENGINE COOLANT LEAKS  (See ON-VEHICLE INSPECTION )
  12. CHECK FOR ENGINE OIL LEAKS  (See REPLACEMENT )
    Fig 4: Locating VVT Sensor Bolt (For Bank 1 Intake Side)
    G04973864Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL V-BANK COVER SUB-ASSEMBLY  (See INSTALLATION )
  14. INSTALL COWL TOP OUTER PANEL OUTER SUB-ASSEMBLY  (See INSTALLATION  )
  15. INSTALL WINDSHIELD WIPER LINK ASSEMBLY 

    HINT:

    (See INSTALLATION )

Chapter Navigation
Return to Chapter: VVT Sensor
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.