Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
How To Proceed With Troubleshooting
HINT:
The intelligent tester can be used in steps  2,  3,  4,  6 and  9.
- VEHICLE BROUGHT TO WORKSHOPÂ
- CONNECT INTELLIGENT TESTER TO DLC3Â
HINT:
If the display indicates a communication fault in the tester, inspect the DLC3.
- CHECK DTC AND FREEZE FRAME DATAÂ
- Check for DTC(s) and freeze frame data (See FREEZE FRAME DATAÂ
).
HINT:
Record or print the DTCs and freeze frame data, if necessary.
- Check for DTC(s) and freeze frame data (See FREEZE FRAME DATAÂ
).
- CLEAR DTC AND FREEZE FRAME DATAÂ
- Clear the DTC(s) and freeze frame data (See FREEZE FRAME DATAÂ ).
- CONDUCT VISUAL INSPECTIONÂ
- SET CHECK MODE DIAGNOSISÂ
- Set the check mode (See CHECK MODE PROCEDUREÂ ).
- CONFIRM PROBLEM SYMPTOMSÂ
HINT:
If the engine does not start, perform steps  9 and  11 first.
ResultÂ
RESULT CHARTResult Proceed to Malfunction does not occur A Malfunction occurs B B: GO TO STEPÂ Â 9
A: Go to Next StepÂ
- SIMULATE SYMPTOMSÂ
- CHECK FOR DTCSÂ
- Check for DTCs (See DTC CHECK/CLEARÂ
).
ResultÂ
RESULT CHARTResult Proceed to Trouble code A No code B
B: GO TO STEPÂ Â 11
A: Go to Next StepÂ
- Check for DTCs (See DTC CHECK/CLEARÂ
).
- REFER TO "DTC CHART"
HINT:
Refer to the DTC chart (See DIAGNOSTIC TROUBLE CODE CHARTÂ ).
GO TO STEPÂ Â 13
- CONDUCT BASIC INSPECTIONÂ
HINT:
Refer to "BASIC INSPECTIONÂ "
ResultÂ
RESULT CHARTResult Proceed to Malfunctioning parts not confirmed A Malfunctioning parts confirmed B B: GO TO STEPÂ Â 16
A: Go to Next StepÂ
- REFER TO "PROBLEM SYMPTOMS TABLE"
HINT:
Refer to "PROBLEM SYMPTOMS TABLEÂ "
ResultÂ
RESULT CHARTResult Proceed to Malfunctioning circuit confirmed A Malfunctioning parts confirmed B B: GO TO STEPÂ Â 16
A: Go to Next StepÂ
- CHECK ECM POWER SOURCE CIRCUITÂ
HINT:
Refer to "ECM POWER SOURCE CIRCUITÂ "
- CONDUCT CIRCUIT INSPECTIONÂ
ResultÂ
RESULT CHARTResult Proceed to Malfunction not confirmed A Malfunction confirmed B B: GO TO STEPÂ Â 17
A: Go to Next StepÂ
- CHECK FOR INTERMITTENT PROBLEMSÂ
HINT:
Refer to "CHECK FOR INTERMITTENT PROBLEMSÂ "
GO TO STEPÂ Â 17
- CONDUCT PARTS INSPECTIONÂ
- IDENTIFY PROBLEMÂ
- ADJUST AND/OR REPAIRÂ
- CONDUCT CONFIRMATION TESTÂ
ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
