Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Lexus LS 430FACTORY OEM SERVICE PROCEDURE
Specifications Index
LS430 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Axle Nut/Hub Nut | |||
| Front | 69 N.m (700 kgf.cm 51 ft.lbf) | ||
| Rear | 290 N.m (2,960 kgf.cm 214 ft.lbf) Β |
||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | SERVICE DATA | ||
| Drum Brakes | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Charging | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Drive Belts | |||
| Adjustment | ON-VEHICLE INSPECTION | ||
| Belt Routing | REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | 93 to 123 kPa (0.95 to 1.25 kgf/cm2 , 13.5 to 17.8 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | at idle, 29 kPa (0.3 kgf.cm2
, 43 psi) or more at 3,000 rpm, 294 - 588 kPa (3.0 - 6.0 kgf.cm2 , 43 - 85 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | 1st: 49 N.m (500 kgf.cm, 36 ft lbs) 2nd: Turn 90Β° |
||
| Fuel System | |||
| Pressure Specification | SERVICE DATA | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Spark Plug (Type = ND SK20R11; NGK IFR6A11) | |||
| Gap | 1.0 to 1.1 mm (0.039 to 0.043 in.) | ||
| Torque | 18 N.m (184 kgf.cm, 13 ft. lbs) | ||
| Starting | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Wheel Alignment | |||
| Front | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Rear | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATION | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 N.m (1,050 kgf.cm, 76 ft lbs.) | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
