Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- PERFORM ACTIVE TEST (OPERATE C/OPN RELAY)
- Connect the hand-held tester to the CAN VIM. Then connect the CAN VIM to the DLC3.
- Turn the ignition switch ON and turn the hand-held tester ON.
- Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD.
- Check the relay operation while operating it using the hand-held tester.
OK: Operating noise can be heard from the relay.
OK: Go to step 6
NG: Go to next step
- INSPECT FUSE (IGN)
- Remove the IGN fuse from the engine room No. 1 R/B.
- Measure the resistance of the fuse.
Standard: Below 1 Ω
NG: REPLACE FUSE
OK: Go to next step
- INSPECT RELAY (Marking: C/OPN)
- Remove the C/OPN relay from the engine room No. 1 R/B.
- Measure the resistance of the relay.
Standard:
C/OPN RELAY - RESISTANCE TABLETester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω (when battery voltage is applied to terminals 1 and 2) NG: REPLACE RELAY
OK: Go to next step
- INSPECT RELAY (Marking: IG2)
- Remove the IG2 relay from the engine room No. 1 R/B.
- Measure the resistance of the relay.
Standard:
IG2 RELAY - RESISTANCE TABLETester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω (when battery voltage is applied to terminals 1 and 2) NG: REPLACE RELAY
OK: Go to next step
- CHECK ECM (FC VOLTAGE)
- Turn the ignition switch ON.
- Measure the voltage of the ECM connector.
Standard:
ECM CONNECTOR - VOLTAGE TABLETester Connection Specified Condition E3-14 (FC) - Body ground 9 to 14 V NG: REPAIR OR REPLACE HARNESS AND CONNECTOR
OK: REPLACE ECM (See REPLACEMENT )
- INSPECT RELAY (Marking: F/PMP)
- Remove the F/PMP relay from the engine room No. 1 R/B.
- Measure the resistance of the relay.
Standard:
F/PMP RELAY - RESISTANCE TABLETester Connection Specified Condition 3 - 4 Below 1 Ω 3 - 4 10 kΩ or more (when battery voltage is applied to terminals 1 and 2) NG: REPLACE RELAY
OK: Go to next step
- INSPECT FUEL PUMP
- Check the resistance of the fuel pump.
- Measure the resistance between terminals 4 and 5.
Standard: 0.2 to 3.0 Ω at 20°C (68°F)
- Check the operation of the fuel pump.
- Apply battery voltage to both the terminals. Check that the pump operates.
NOTE:- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
- Keep fuel pump as far away from the battery as possible.
- Check the resistance of the fuel pump.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
