Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK FOR DTCS
- Operate any of the switches on the power window regulator master switch assy. Check if any DTCs are output.
RESULT:
DTC OUTPUT RESULTResult Proceed to No DTC is output A DTC is output B B: Go to DIAGNOSTIC TROUBLE CODE CHART
A
- READ DATA LIST USING HAND-HELD TESTER
- Connect the hand-held tester (with CAN VIM) to the DLC3.
- Turn the ignition switch ON and press the hand-held tester main switch ON.
- Select the items below in the DATA LIST, and read the displays on the hand-held tester.
DRIVER DOOR ECU:
DATA LIST REFERENCEItem Measurement Item / Display (Range) Normal Condition Diagnostic Note P/W AUTO SW D door P/W auto switch ON/OFF ON: Driver door power window auto switch operates OFF: Driver door power window auto switch does not operate - OK: "ON" (switch is operated) appears on the screen.
NG: Go to step 3
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
- INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSY
- Remove the switch.
- Disconnect the P13 switch connector.
- Measure the resistance and voltage of the switch when the switch is operated.
Standard:
DRIVER SWITCH
POWER WINDOW REGULATOR MASTER SWITCH RESISTANCE AND VOLTAGE SPECIFICATIONSTester Connection Switch Position Specified Condition 6 (PW) - 16 (AUTO) AUTO UP Below 50 Ω 6 (PW) - 20 (DUP) AUTO UP Below 50 Ω 6 (PW) - 20 (DUP) MANUAL UP Below 50 Ω - OFF - 6 (PW) - 11 (DDN) MANUAL DOWN Below 10 Ω 6 (PW) - 16 (AUTO) AUTO DOWN Below 10 Ω 6 (PW) - 11 (DDN) AUTO DOWN Below 50 Ω - Using an electrical tester, check if the diodes are functioning normally.
HINT:
- As the switch has diodes, a resistance inspection cannot be performed. Use the tester's diodes check function to check the diodes.
- Connect the tester's leads as shown in the Fig 2 below. If the leads are not connected correctly, the readings will not be accurate. Connect the tester's positive (+) lead to the diode's positive (+) side, and the negative (-) lead to the diode's negative (-) side.
- Set the function selector switch to diode check function mode, and check that the diodes are functioning normally.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Passenger side switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Rear LH switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Rear RH switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REFERENCE (USING FOR TOYOTA ELECTRICAL TESTER):
VOLTAGE SPECIFICATIONSTest lead Specified Condition Normal direction 0.4 to 0.8 V If the result is not as specified, replace the switch assy.
WINDOW LOCK SWITCH
WINDOW LOCK SWITCH SPECIFIED CONDITIONSSwitch Condition Measurement Condition Specified Condition NORMAL Battery positive (+) --> Terminal 6 (PW) Battery negative (-) --> Terminal 10 (E) All 4 switches illuminate LOCK Battery positive (+) --> Terminal 6 (PW) Battery negative (-) --> Terminal 10 (E) Driver door window switch illuminates NG: REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSY
OK: Go to next step
- CHECK WIRE HARNESS (POWER WINDOW REGULATOR MASTER SWITCH ASSY - DRIVER DOOR ECU)
- Disconnect the P13 switch connector.
- Disconnect the D24 and D25 ECU connectors.
- Measure the resistance of the wire harness side connectors.
Standard
RESISTANCE SPECIFICATIONSTester Connection Specified Condition P13-6 (PW) - D24-22 (PWS) Below 1 Ω P13-10 (E) - D24-30 (PWE) Below 1 Ω P13-16 (AUTO) - D24-2 (AUTO) Below 1 Ω P13-20 (DUP) - D24-23 (MUP) Below 1 Ω P13-11 (DDN) - D24-25 (MDN) Below 1 Ω P13-3 (DT1) - D24-6 (DT1) Below 1 Ω P13-4 (DT2) - D24-5 (DT2) Below 1 Ω P13-5 (DT3) - D24-4 (DT3) Below 1 Ω P13-13 (SC1) - D24-17 (SC1) Below 1 Ω P13-14 (SC2) - D24-16 (SC2) Below 1 Ω P13-15 (SC3) - D24-15 (SC3) Below 1 Ω P13-7 (W/L) - D25-16 (WLSW) Below 1 Ω P13-6 (PW) or D24-22 (PWS) - Body ground 10 kΩ or higher P13-10 (E) or D24-30 (PWE) - Body ground 10 kΩ or higher P13-16 (AUTO) or D24-2 (AUTO) - Body ground 10 kΩ or higher P13-20 (DUP) or D24-23 (MUP) - Body ground 10 kΩ or higher P13-11 (DDN) or D24-25 (MDN) - Body ground 10 kΩ or higher P13-3 (DT1) or D24-6 (DT1) - Body ground 10 kΩ or higher P13-4 (DT2) or D24-5 (DT2) - Body ground 10 kΩ or higher P13-5 (DT3) or D24-4 (DT3) - Body ground 10 kΩ or higher P13-13 (SC1) or D24-17 (SC1) - Body ground 10 kΩ or higher P13-14 (SC2) or D24-16 (SC2) - Body ground 10 kΩ or higher P13-15 (SC3) or D24-15 (SC3) - Body ground 10 kΩ or higher P13-7 (W/L) or D25-16 (WLSW) - Body ground 10 kΩ or higher NG: REPAIR OR REPLACE HARNESS AND CONNECTOR
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
