Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Section 183 (Power Door Lock Control System): Inspection
- INSPECT FRONT DOOR W/MOTOR LOCK ASSY LH
- Apply battery voltage and inspect operation of the door lock motor.
Standard:
If operation is not as specified, replace the door lock assy.
- Inspect the resistance of the position switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Door Lock Position Specified Condition 7 - 8 Lock 10 kΩ or higher Unlock Below 1 Ω If the result is not as specified, replace the door lock assy.
- Inspect the resistance of the door lock and unlock switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Door Lock Position Specified Condition 7 - 9 Lock Below 1 Ω 7-9, 7 - 10 OFF - 7 - 10 Unlock Below 1 Ω If the result is not as specified, replace the door lock assy.
- Apply battery voltage and inspect operation of the door lock motor.
- INSPECT FRONT DOOR W/MOTOR LOCK ASSY RH
- Apply battery voltage and inspect operation of the door lock motor.
Standard:
If operation is not as specified, replace the door lock assy.
- Inspect the resistance of the position switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Door Lock Position Specified Condition 7-8 Lock 10 kΩ or higher Unlock Below 1 Ω If the result is not as specified, replace the door lock assy.
- Inspect the resistance of the door lock and unlock switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Door Lock Position Specified Condition 6 - 8 Lock Below 1 Ω 5 - 8, 6 - 8 OFF - 5 - 8 Unlock Below 1 Ω If the result is not as specified, replace the door lock assy.
- Apply battery voltage and inspect operation of the door lock motor.
- INSPECT REAR DOOR LOCK ACTUATOR ASSY LH
- Apply battery voltage and inspect operation of the door lock motor.
Standard:
If operation is not as specified, replace the door lock assy.
- Inspect the resistance of the position switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Door Lock Position Specified Condition 1 - 4 Lock 10 kΩ or higher Unlock Below 1 Ω If the result is not as specified, replace the door lock assy.
- Apply battery voltage and inspect operation of the door lock motor.
- INSPECT REAR DOOR LOCK ACTUATOR ASSY RH
- Apply battery voltage and inspect operation of the door lock motor.
Standard:
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
If operation is not as specified, replace the door lock assy.
- Inspect the resistance of the position switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Door Lock Position Specified Condition 1 - 4 Lock 10 kΩ or higher Unlock Below 1 Ω If the result is not as specified, replace the door lock assy.
- Apply battery voltage and inspect operation of the door lock motor.
- INSPECT BACK DOOR LOCK ASSY (W/O CLOSER)
- Check operation of the door lock.
- Using a screwdriver, push the latch in order to put the back door lock in the locked condition (full-latch position).
- Connect the battery positive (+) lead to terminal 3 and the battery negative (-) lead to terminal 1. Then, check operation of the latch.
Standard: The latch turns to the open-latch position
If operation is not as specified, replace the door lock assy.
- Inspect motor operation when battery voltage is applied to the terminals.
Standard:
If operation is not as specified, replace the door lock assy.
- Check the back door courtesy switch resistance.
- Check the resistance between the terminals of the courtesy switch.
Standard:
RESISTANCE SPECIFICATIONDoor Lock Latch Position Terminal No. Specified Condition Open-latch position 5 - 6 Below 1 Ω Full-latch position 10 kΩ or higher If the result is not as specified, replace the door lock assy.
- Check operation of the door lock.
- INSPECT BACK DOOR LOCK ASSY (W/ CLOSER)
- Check operation of the door lock.
- Using a screwdriver, push the latch in order to put the back door lock in the locked condition (full-latch position).
- Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2. Then, check operation of the latch.
Standard: The latch turns to the open-latch position
- Inspect motor operation when battery voltage is applied to the terminals.
Standard:
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
If operation is not as specified, replace the door lock assy.
- Check the back door courtesy switch resistance.
- Check the resistance between the terminals of the courtesy switch.
Standard:
RESISTANCE SPECIFICATIONDoor Lock Latch Position Terminal No. Specified Condition Open-latch position, Half-latch position 3 - 4 Below 1 Ω Full-latch position, Over-latch position 10 kΩ or higher If the result is not as specified, replace the door lock assy.
- Check the back door latch switch resistance.
- Check the resistance between the terminals of the latch switch.
Standard:
RESISTANCE SPECIFICATIONDoor Lock Latch Position Terminal No. Specified Condition Open-latch position, Over-latch position 4 - 5 Below 1 Ω Half-latch position, Full-latch position 10 kΩ or higher If the result is not as specified, replace the door lock assy.
- Check the position switch resistance.
- Connect the battery positive (+) lead to connector terminal 1 and the negative (-) lead to connector terminal 2.
Standard:
RESISTANCE SPECIFICATIONDoor Lock Latch Position Terminal No. Specified Condition Any position other than motor stop position (Motor in operation) 4 - 6 Below 1 Ω Motor stop position (Gear in original position 10 kΩ or higher If the result is not as specified, replace the door lock assy.
- Check operation of the door lock.
- INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSY
- Inspect the resistance of the switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Switch Position Specified Condition 1 - 5 Lock Below 1 Ω 1 - 5, 1 - 8 OFF 10 kΩ or higher 1 - 8 Unlock Below 1 Ω If the result is not as specified, replace the switch assy.
- Inspect the resistance of the switch.
- INSPECT DOOR CONTROL SWITCH ASSY
- Inspect the resistance of the switch.
Standard:
RESISTANCE SPECIFICATIONTerminal No. Switch Position Specified Condition 3 - 6 Lock Below 1 Ω 3 - 5,3 - 6 OFF 10 kΩ or higher 3 - 5 Unlock Below 1 Ω If the result is not as specified, replace the switch assy.
- Inspect the resistance of the switch.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
