Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Lexus ES 330FACTORY OEM SERVICE PROCEDURE
Torque Specification
WARNING: This page is about a different car, the 2005 Toyota Sienna. However, it is still accessible from the selected car via links, so may be relevant.
BRAKE TORQUE SPECIFICATION
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Wheel nut | 103 | 1,050 | 76 | |
| Brake line union nut | 15 | 155 | 11 | |
| Brake booster clevis lock nut | 26 | 260 | 20 | |
| Brake pedal support assy x Body | 16 | 160 | 12 | |
| Brake pedal bracket No. 3 x brake pedal support reinforcement | 19 | 194 | 14 | |
| Brake pedal x brake pedal support assy | 34 | 350 | 25 | |
| Brake booster assy x Body | 16 | 160 | 12 | |
| Brake master cylinder (3rd chamber) bleeder plug | 11 | 112 | 8 | |
| Brake master cylinder sub-assy x master cylinder (3rd chamber) | 25 | 255 | 18 | |
| Brake tube clamp x body | 5.4 | 55 | 48 in.lbf | |
| Front disc brake bleeder plug | 8.3 | 85 | 74 in.lbf | |
| Front brake cylinder mounting x Steering knuckle | 107 | 1,090 | 79 | |
| Front disc brake cylinder x Front disc brake cylinder mounting | 34 | 350 | 25 | |
| Front disc brake caliper x Flexible hose | 29 | 296 | 21 | |
| Rear disc brake bleeder plug | 8.3 | 85 | 74 in.lbf | |
| Rear disc brake cylinder mounting x Steering knuckle | 88 | 900 | 65 | |
| Rear disc brake cylinder x Rear disc brake cylinder mounting | 34 | 35 | 25 | |
| Rear disc brake caliper x Flexible hose | 23 | 235 | 17 | |
| Rear drum brake bleeder plug | 11 | 112 | 8 | |
| Rear wheel cylinder assy x Baking plate | 10 | 102 | 7 | |
| Brake actuator x Brake actuator bracket | w/ABS: | 5.4 | 55 | 48 in.lbf |
| w/VSC: | 5.4 | 55 | 48 in.lbf | |
| Brake actuator bracket x Body | 20 | 199 | 14 | |
| Front speed sensor wire harness clamp x shock absorber | 19 | 192 | 14 | |
| Front speed sensor x Steering knuckle | 8.0 | 82 | 71 in.lbf | |
| Rear speed sensor wire harness clamp x Body | 8.0 | 82 | 71 in.lbf | |
| Rear speed sensor wire harness clamp x Rear axle | 8.0 | 82 | 71 in.lbf | |
| Yaw rate sensor bracket x Body | 13 | 136 | 10 | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.