Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2004LX 470 V8-4.7L (2UZ-FE)REPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINECYLINDER HEAD ASSEMBLYSYSTEM SPECIFICATIONSSERVICE SPECIFICATIONS
2004 Lexus LX 470 V8-4.7L (2UZ-FE)
Service Specifications
2004 Lexus LX 470 V8-4.7L (2UZ-FE)SECTION Service Specifications
SERVICE SPECIFICATIONS
Cylinder Head:
Warpage:
Maximum 0.10 mm (0.039 inch)
Bolt Thread Inside Diameter:
Standard 9.810 - 9.960 mm (0.3862 - 0.3921 inch)
Minimum 9.70 mm (0.3819 inch)
Lifter Bore Diameter 31.000 - 31.016 mm (1.2205 - 1.2211 inch)
Oil Clearance:
Standard 0.024 - 0.050 mm (0.0009 - 0.0020 inch)
Maximum 0.07 mm (0.0028 inch)
TORQUE SPECIFICATIONS
Cylinder Head To Cylinder Block:
1st Turn 32 Nm ( 326 kgf-cm 24 ft. lbs.)
2nd Turn 90°
3rd Turn 90°
Camshaft Bearing Cap To Cylinder Head:
Bolt C 7.5 Nm (66 inch lbs.)
Others 16 Nm (12 ft. lbs.)
Engine Hanger To Cylinder Head 37 Nm ( 27 ft. lbs.)
Front Water Bypass Joint, Rear Water Bypass Joint To:
Cylinder Head 18 Nm (13 ft. lbs.)
Timing Belt Rear Plate To:
Cylinder Head 7.5 Nm (66 inch lbs.)
Cylinder Head:
Warpage:
Maximum 0.10 mm (0.039 inch)
Bolt Thread Inside Diameter:
Standard 9.810 - 9.960 mm (0.3862 - 0.3921 inch)
Minimum 9.70 mm (0.3819 inch)
Lifter Bore Diameter 31.000 - 31.016 mm (1.2205 - 1.2211 inch)
Oil Clearance:
Standard 0.024 - 0.050 mm (0.0009 - 0.0020 inch)
Maximum 0.07 mm (0.0028 inch)
TORQUE SPECIFICATIONS
Cylinder Head To Cylinder Block:
1st Turn 32 Nm ( 326 kgf-cm 24 ft. lbs.)
2nd Turn 90°
3rd Turn 90°
Camshaft Bearing Cap To Cylinder Head:
Bolt C 7.5 Nm (66 inch lbs.)
Others 16 Nm (12 ft. lbs.)
Engine Hanger To Cylinder Head 37 Nm ( 27 ft. lbs.)
Front Water Bypass Joint, Rear Water Bypass Joint To:
Cylinder Head 18 Nm (13 ft. lbs.)
Timing Belt Rear Plate To:
Cylinder Head 7.5 Nm (66 inch lbs.)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.